Tacoma World Forums

Tacoma World Forums (http://www.tacomaworld.com/forum/)
-   1st Gen Tacoma Marketplace (http://www.tacomaworld.com/forum/1st-gen-tacoma-marketplace/)
-   -   Total Chaos - Gusseted Tacoma/4Runner spindles (http://www.tacomaworld.com/forum/1st-gen-tacoma-marketplace/285166-total-chaos-gusseted-tacoma-4runner-spindles.html)

adrn1986 07-05-2013 08:01 AM

Total Chaos - Gusseted Tacoma/4Runner spindles
 
I've started my 4WD conversion and no longer need the 2WD spindels.

-Good condition, just need to be cleaned and installed
-Toyota Factory bearings pressed in 19k miles ago
-TC gussets already welded on
-No ball joints, just the spindle and hub assembly
-TC SLUG ADAPTER WELDED IN PLACE / WILL ONLY WORK WITH TOTAL CHAOS UCA's (maybe other after market UCA's but I cannot confirm)

Located in Ricerside Ca, 92504
$150 + shipping. (27"x12"x6" @ 55lbs , ups.com has quick quotes for those of you who would like to know shipping cost)
Adrn1986@yahoo.com email me if you'd like to get a hold of me right away.

http://i35.photobucket.com/albums/d1...ps8b578c03.jpg

Adrian

Vegabeltran 07-14-2013 10:27 PM

Are these stock spindles?

adrn1986 07-29-2013 06:50 PM

Quote:

Originally Posted by Vegabeltran (Post 7163232)
Are these stock spindles?

Yes, stock spindles with Total Chaos spindle gussets welded on.

adrn1986 07-29-2013 06:50 PM

Cleaned up and painted. Bolt on and go...

http://i35.photobucket.com/albums/d1...pse7b6830d.jpg

http://i35.photobucket.com/albums/d1...psa0331cb8.jpg

adrn1986 08-07-2013 01:18 PM

Bump

adrn1986 08-13-2013 03:06 PM

$150 Shipped

adrn1986 08-22-2013 03:09 PM

Bump

adrn1986 09-05-2013 10:17 AM

Bump

Finks99Taco 09-05-2013 05:49 PM

Would there be any way to tell if another UCA would work with these?

adrn1986 09-06-2013 06:59 AM

I'm 99% sure that most other brands will work due to the fact that hiem spacer dimentions are pretty standard. If your a arm uses a 3/4" bolt, which most do, it should fit.

Finks99Taco 09-06-2013 02:48 PM

Of course I don't have the UCAs with me to measure and can't find online what the bolt size is. I have the LR UCAs and was figuring since the truck is parked with blow LCA ball joints, I figure I can rebuild everything on your spindles and bolt the whole assembly in.

yumyumtaco 09-06-2013 11:18 PM

so... is there anything saying you CANT put these on a 96 taco 5-lug truck? other than the fact that your rear hubs will have 5 lugs and your fronts will have 6...?

adrn1986 09-08-2013 11:53 AM

Quote:

Originally Posted by Finks99Taco (Post 7395708)
Of course I don't have the UCAs with me to measure and can't find online what the bolt size is. I have the LR UCAs and was figuring since the truck is parked with blow LCA ball joints, I figure I can rebuild everything on your spindles and bolt the whole assembly in.

Good idea. However, I believe the adjustable Light Racing a-arms use a factory style ball joint with a tapper and castle nut. Not a traditional uniball UCA with a spindle 'slug adapter.' For the 96-04's uniball UCA's use a uniball pivot, hiem spacers, an adapter and a long bolt to eliminate the factory ball joint.

That just my guess biased on what I've seen, I could be wrong.

adrn1986 09-08-2013 12:03 PM

Quote:

Originally Posted by yumyumtaco (Post 7397608)
so... is there anything saying you CANT put these on a 96 taco 5-lug truck? other than the fact that your rear hubs will have 5 lugs and your fronts will have 6...?

Sorry dude, competently different spindles for Pre-Runner & 4WD's vs. the 5 Lug Tacoma. I don't believe any front suspension parts are compatible between the two. Unless you're willing to rip it all out and convert it. :)

adrn1986 09-08-2013 12:34 PM

So I did a little bit of research and it looks to me like
-Total Chaos 1”
-All Pro 1"
-Camburg 1"
are compatible with one another.

Camburg 1.25" are NOT compatible.
(Not 100% confirmed, just a few minuets of surfing sites to check)


Off Total Chaos’s install page:
“6 10350 2 2 BOLT, 3/4" x 5.00L

Off of All-Pro’s install page:
“12. Attach the chromoly a-arm to the spindle. Install 3/4”x5” bolt and torque to specification, 90 ft. lbs.”


Camburg’s install page:
“Swing down the upper arm so the spindle adaptor inserts
into the uniball. Insert the upper uniball spacer into the top
of the uniball and bolt together with the supplied 5/8” G9 bolt
and locking nut. Using a 15/16” wrench and 15/16” socket,
torque to 125-135 ft/lbs. Make sure the spacers are fully
seated in the uniball prior to tightening. Refer to diagram 4.2”

yumyumtaco 09-08-2013 05:27 PM

oh y badd.. i guess if i would have looked closer i would have seen the "4WD" in the post... lol

adrn1986 09-16-2013 03:09 PM

SOLD


All times are GMT -7. The time now is 05:22 PM.