Mike "Wuzzy121". Rest in peace, brother

Go Back   Tacoma World Forums > Tacoma Discussion > 1st Gen. Tacomas

Notices

My rear o2 sensor has no nuts

Reply
 
Thread Tools Search this Thread
Old 06-21-2011, 12:50 PM   #1
meatman [OP] meatman is online now
I deal with dead animals
meatman is one of the sharper tools in the shedmeatman is one of the sharper tools in the shedmeatman is one of the sharper tools in the shedmeatman is one of the sharper tools in the shedmeatman is one of the sharper tools in the shedmeatman is one of the sharper tools in the shedmeatman is one of the sharper tools in the shedmeatman is one of the sharper tools in the shedmeatman is one of the sharper tools in the shedmeatman is one of the sharper tools in the shedmeatman is one of the sharper tools in the shed
 
meatman's Avatar
Name: Greg
Joined: Mar 2011, #53630
Location: Murphy N.C.
Gender: Male
Posts: 2,140
meatman's Tacoma Gallery
My rear o2 sensor has no nuts

So i went a did an oil change and when i got done and drove over to recycle the old oil and i started to hear a nasty rattling sound. I thought it was going to be the rear skid plate and after i removed it again (i took it off to do oil change) i thought i would grease up all the spots couldnt been happier they were all in perfect allignment and easy to get to.
As i shimmied to the rear of the truck i noticed a small shield hanging funny and low and behold there were no nuts holding it on. long story short what a pain to replace. F.... it im gonna pay someone to change my oil from now on Ha ha ha. i am supprised it didnt throw a code
  Reply With Quote
Old 06-21-2011, 03:22 PM   #2
Senior Member
DblCabMN is one of the sharper tools in the shedDblCabMN is one of the sharper tools in the shedDblCabMN is one of the sharper tools in the shedDblCabMN is one of the sharper tools in the shedDblCabMN is one of the sharper tools in the shedDblCabMN is one of the sharper tools in the shedDblCabMN is one of the sharper tools in the shedDblCabMN is one of the sharper tools in the shedDblCabMN is one of the sharper tools in the shedDblCabMN is one of the sharper tools in the shedDblCabMN is one of the sharper tools in the shed
 
DblCabMN's Avatar
Joined: Mar 2011, #53498
Location: Mpls, Minnesota
Gender: Male
Posts: 669
DblCabMN's Tacoma Gallery
when i took my truck in to get my new muffler welded on, the guys came out and said the same of my rear o2 - i asked to see it, sure enough, no nuts, no heat shield. They had a couple new laying around and slapped 'em on for free.
  Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Similar Threads
Thread Thread Starter Forum Replies Last Post
rear o2 sensor - DONE! bowyer2002 1st Gen. Tacomas 65 10-08-2014 12:17 PM
Help needed for a live reading of rear o2 sensor (bank 1 sensor 2) geoff06 Technical Chat 7 11-30-2011 04:57 AM
Rear o2 sensor wiring? ETaco23 Technical Chat 11 12-24-2009 01:05 PM
how to replace rear O2 sensor on 2003 xtracab? jmm2003 Technical Chat 5 02-01-2009 05:58 AM
3.4 coil packs, rear O2 sensor, water temp sensor glassdoc Buy / Sell / Trade 6 01-28-2009 06:51 AM


Copyright © 2014 Tacoma Forum. Tacoma World is not owned by, or affiliated with Toyota Motor Corporation.