DIY leather arm rests

reid · 09-01-2007, 01:11 AM

Here are the steps I went through to replace my crappy fabric arm rests with leather covered ones. Too many images so I will use two posts.

1. Using a small flathead screwdriver pry open the screw covers behind the inside door handle and the door latch.

2. With the same screwdriver push in on the center of the fastener that is on the door panel near the mirror. Then pull it out.

3. To remove the inner panel, you have to pry the bottom and both sides away from the door. I did this with a larger screwdriver. When this is done you should be able to remove the inner door panel by lifting it up. There are hooks underneath the window felt that hang the door panel on the door.

4. Once the panel is removed, turn it over and look at the back of the arm rest. The arm rest is fastened to the door panel with a series of small melt points. I used a 3/8" drill bit to drill down about 1/4" into the centre of the melt points. Do not drill too far because you will need enough plastic to put screws in later. The melt points are like plastic rivets.

5. Once the melt point are drilled out you should be able to pry the armrest off. Next remove the old fabric.

reid · 09-01-2007, 01:11 AM

6. Now cut out a piece of leather slightly larger than the original fabric.

7. Use a spray adhesive to attach the leather to the arm rest. Then cut off the excess.

8. Once it is dry, place it back in the door panel. Use #10 x 1/2" sheet metal screws to attach the arm rest where the melt points were.

9. Then all you have to do is put the door panel back in your truck the opposite way you took it out. Here is a finished picture.

Any questions, just ask. Hope this helps.

tacomaman06 · 09-01-2007, 06:28 AM

now, that is a damn nice looking cover man

!!! im thinking i will be doing something similar very soon!!! so, about how long did it take you to do this??? btw........that black leather is friggin awesome man!!

reid · 09-01-2007, 09:46 AM

Thanks, I have done a lot of interior work, I make motorcycle seats. It only took me 1 hour. Anyone could do it in about the same amount of time.

Leather is much easier to stretch than vinyl. Plus it looks killer.

007Tacoma · 09-02-2007, 08:06 AM

I was going to say that we should make this a sticky, but somebody beat me too it.

Congrats, Reid, that is an awesome DIY, and it looks great!

Good job!

rick · 09-02-2007, 09:38 AM

damn nice reid

LQQKatmy06 · 09-02-2007, 11:59 AM

Looks good, I was thinking of doing the same thing but have not had the door panels off yet. Thanx for taking the plunge takes all the guess work out of it.

reid · 09-02-2007, 12:42 PM

I have decided that I will try to do the center console arm rest and rear access cab seat back too.

LQQKatmy06 · 09-02-2007, 07:24 PM

Hey Reid,
Do you think there is enough room to put leather over the factory cloth and get it all back in place?

reid · 09-02-2007, 08:52 PM

You could if you used thin enough leather. The thickness of the leather is measured by weight. I think I used 4oz. leather. If you used this weight you could, but anything heavier would be too thick.

pb2themax · 09-02-2007, 09:39 PM

No need to "pry" on the door panel. The word "pry" sounds painful to your plastic door panel. Once you have the mirror sail, 2 screws and 1 pin removed, just grab the storage compartment area at the bottom of the door panel and pull out real fast. It'll pop loose.

Then lift the panel up to pop it loose. Then reach under and pop the control panel loose, then hang the door panel back on the window lip to hold the door panel while you disconnect the plug from wiring harness. The drivers side controls can be hard to release. It's like a two peice harness. Then once it's disconnected you can remove the door panel and proceed.

Before you re-install the mirror sail, use your fingernails to pull out those 3 plastic clips and put them on the sail, then install the sail. If you don't remove them the sail will push the clips down into the interior of the door, and you'll have to fish em out.

Good work with the leather, reid.

pb2themax · 09-02-2007, 09:46 PM

Quote:

Originally Posted by LQQKatmy06

Hey Reid,
Do you think there is enough room to put leather over the factory cloth and get it all back in place?

I doubt the adhesive would stick to the factory cloth very good. I wouldn't do it.

reid · 09-03-2007, 12:36 PM

If you buy the right adhesive you can stick leather to fabric. I have used it before, but it is $25.00 a can.

I found the passanger side electrical connections harder than the drivers side. My drivers side only had on econnection and the passanger side had two. Plus the passanger side wires were much shorter on my truck.

nd · 09-04-2007, 11:23 AM

I was skeptical when i saw this thread but i have to admit i really like the look of it and it doens't look to hard to do. I'm glad this one was turned into a "sticky"

Viper-2 · 09-13-2007, 04:28 AM

Yeah I was skeptical too, but it looks real nice. I don't know if I would do it, but it still looks real good.

Jesse · 09-14-2007, 02:30 PM

Where can you get that leather. Is it really leather, or leather lookalike?

reid · 09-15-2007, 08:20 PM

It is real leather. I buy my leather at a leather supply store here in Vancouver. You could probably pick some up from a fabric/sewing store or a furniture upholstery shop.

tucsontoast · 09-16-2007, 06:58 PM

Reid,

All I have to say is "SUWEEEEEET!!!" The time you took to detail the photographs and outline the instructions is greatly appreciated. I'm definitely going to perform this mod on my "YOCA" cuz I work for a living, and this will definitely be easier to clean than the factory fabric.

Thaanks Maaan!

jhodge83 · 09-16-2007, 07:40 PM

looks good. i'm thinking about getting some black/grey leather seat covers, so black leather arm rests would look great

babrown0475 · 09-28-2007, 05:53 PM

That is lookin mighty fine. I do believe I'll be doin this!!

09-01-2007, 01:11 AM	#2
reid Senior Member Joined: May 2007, #1645 Location: Vancouver BC Canada Posts: 260 2007 V6 Access Cab 2007 Access Cab Manual V6 4.0L Magna Flow stainless cat-back, 3" Toytec Lift, 32" Mickey Thompsons	6. Now cut out a piece of leather slightly larger than the original fabric. 7. Use a spray adhesive to attach the leather to the arm rest. Then cut off the excess. 8. Once it is dry, place it back in the door panel. Use #10 x 1/2" sheet metal screws to attach the arm rest where the melt points were. 9. Then all you have to do is put the door panel back in your truck the opposite way you took it out. Here is a finished picture. Any questions, just ask. Hope this helps. __________________ Reid

09-01-2007, 06:28 AM	#3
tacomaman06 Carolina Alliance: Redneck Division Joined: May 2007, #1475 Location: rock hill, sc Age: 29 Posts: 6,101 04 trd tacoma 4x4 v6 double cab 2004 Double Cab Automatic 3.4 v6 westin safari bar/ipf rectangle lights,westin wheel to wheel nerfs(black),vent visors,deck plate mod, gray wire mod, black steelies and emblems....still to come.... afe pro dry s filter..........plus many,many more!!	now, that is a damn nice looking cover man!!! im thinking i will be doing something similar very soon!!! so, about how long did it take you to do this??? btw........that black leather is friggin awesome man!! __________________ i am WILL--my ride=04 tacoma trd 4x4 double cab, v6, auto, black westin wheel to wheel nerfs, black westin safari bar w/ ipf rectangle lights,deck plate mod, grey wire mod, billy 5100's all the way around,black low-pro uws toolbox, black steelies,blacked out emblems......more mods to come!!! http://s202.photobucket.com/albums/aa269/tacomaman06/ www.myspace.com/goodolboy1979

09-01-2007, 09:46 AM	#4
reid Senior Member Joined: May 2007, #1645 Location: Vancouver BC Canada Posts: 260 2007 V6 Access Cab 2007 Access Cab Manual V6 4.0L Magna Flow stainless cat-back, 3" Toytec Lift, 32" Mickey Thompsons	Thanks, I have done a lot of interior work, I make motorcycle seats. It only took me 1 hour. Anyone could do it in about the same amount of time. Leather is much easier to stretch than vinyl. Plus it looks killer. __________________ Reid

09-02-2007, 08:06 AM	#5
007Tacoma Moderator, Super Moderator Joined: Jan 2007, #643 Location: San Antonio, Texas Posts: 4,477 08 PreRunner SR5 Double Cab Long-Bed 2008 Double Cab Automatic 4.0L TacomaWorld.com Sticker, URD True Cold Air Intake, Debadged, Blackened Headlight Mod, 30% Window Tint, Access LE Tonneau, Bed Mat, OEM Daytime Running Lights + On/Off Switch, Fogs-On-Anytime Mod, Alternating Turn-Signal Mod, Canvas Seat Covers, Pioneer Stereo, iPod Connection, PAC steering wheel remote, Homemade Bike Rack (4 bikes), Firestone Destination ATs 265/75R16, COMING SOON - Suspension Upgrade (via TSB)	I was going to say that we should make this a sticky, but somebody beat me too it. Congrats, Reid, that is an awesome DIY, and it looks great! Good job! __________________ Old Ride: 2007 Tacoma PreRunner Access Cab 2.7L I4 w/ 5 speed manual tranny (Impulse Red Pearl) New Ride: 2008 Tacoma PreRunner Double Cab 4.0L V6 w/ 5 speed auto tranny (Black Sand Pearl) *Motto: "I don't mod to go fast. I mod to look good going slow"* Mods: TacomaWorld.com Sticker * URD True Cold Air Intake * Debadged * Black Headlight Mod (BHLM) * 30% Window Tint Access LE Tonneau * Bed Mat * OEM Daytime Running Lights (DRL) w/ Switch * Fogs-On-Anytime Mod * Alternating Turn-Signal Mod Canvas Seat Covers * Pioneer Stereo * iPod Connection * PAC steering wheel remote Homemade Bike Rack (4 bikes) * Firestone Destination ATs 265/75R16

09-02-2007, 11:59 AM	#7
LQQKatmy06 Carolina Alliance Joined: Jul 2007, #2220 Location: T-VILLE, NC Posts: 184	Looks good, I was thinking of doing the same thing but have not had the door panels off yet. Thanx for taking the plunge takes all the guess work out of it. __________________ http://community.webshots.com/user/browbury

09-01-2007, 01:11 AM	#1
reid Senior Member Joined: May 2007, #1645 Location: Vancouver BC Canada Posts: 260 2007 V6 Access Cab 2007 Access Cab Manual V6 4.0L Magna Flow stainless cat-back, 3" Toytec Lift, 32" Mickey Thompsons	DIY leather arm rests Here are the steps I went through to replace my crappy fabric arm rests with leather covered ones. Too many images so I will use two posts. 1. Using a small flathead screwdriver pry open the screw covers behind the inside door handle and the door latch. 2. With the same screwdriver push in on the center of the fastener that is on the door panel near the mirror. Then pull it out. 3. To remove the inner panel, you have to pry the bottom and both sides away from the door. I did this with a larger screwdriver. When this is done you should be able to remove the inner door panel by lifting it up. There are hooks underneath the window felt that hang the door panel on the door. 4. Once the panel is removed, turn it over and look at the back of the arm rest. The arm rest is fastened to the door panel with a series of small melt points. I used a 3/8" drill bit to drill down about 1/4" into the centre of the melt points. Do not drill too far because you will need enough plastic to put screws in later. The melt points are like plastic rivets. 5. Once the melt point are drilled out you should be able to pry the armrest off. Next remove the old fabric. __________________ Reid

09-02-2007, 09:38 AM	#6
rick ` Joined: Mar 2007, #993 Location: clearwater, FL Posts: 1,020	damn nice reid

09-02-2007, 12:42 PM	#8
reid Senior Member Joined: May 2007, #1645 Location: Vancouver BC Canada Posts: 260 2007 V6 Access Cab 2007 Access Cab Manual V6 4.0L Magna Flow stainless cat-back, 3" Toytec Lift, 32" Mickey Thompsons	I have decided that I will try to do the center console arm rest and rear access cab seat back too. __________________ Reid

09-02-2007, 07:24 PM	#9
LQQKatmy06 Carolina Alliance Joined: Jul 2007, #2220 Location: T-VILLE, NC Posts: 184	Hey Reid, Do you think there is enough room to put leather over the factory cloth and get it all back in place? __________________ http://community.webshots.com/user/browbury

09-02-2007, 08:52 PM	#10
reid Senior Member Joined: May 2007, #1645 Location: Vancouver BC Canada Posts: 260 2007 V6 Access Cab 2007 Access Cab Manual V6 4.0L Magna Flow stainless cat-back, 3" Toytec Lift, 32" Mickey Thompsons	You could if you used thin enough leather. The thickness of the leather is measured by weight. I think I used 4oz. leather. If you used this weight you could, but anything heavier would be too thick. __________________ Reid

09-02-2007, 09:39 PM	#11
pb2themax Mod Master Joined: Dec 2006, #500 Posts: 387 TRD Sport 4x4 2005 Double Cab Automatic 4.0	No need to "pry" on the door panel. The word "pry" sounds painful to your plastic door panel. Once you have the mirror sail, 2 screws and 1 pin removed, just grab the storage compartment area at the bottom of the door panel and pull out real fast. It'll pop loose. Then lift the panel up to pop it loose. Then reach under and pop the control panel loose, then hang the door panel back on the window lip to hold the door panel while you disconnect the plug from wiring harness. The drivers side controls can be hard to release. It's like a two peice harness. Then once it's disconnected you can remove the door panel and proceed. Before you re-install the mirror sail, use your fingernails to pull out those 3 plastic clips and put them on the sail, then install the sail. If you don't remove them the sail will push the clips down into the interior of the door, and you'll have to fish em out. Good work with the leather, reid. __________________ My 05 Tacoma CarDomain

09-03-2007, 12:36 PM	#13
reid Senior Member Joined: May 2007, #1645 Location: Vancouver BC Canada Posts: 260 2007 V6 Access Cab 2007 Access Cab Manual V6 4.0L Magna Flow stainless cat-back, 3" Toytec Lift, 32" Mickey Thompsons	If you buy the right adhesive you can stick leather to fabric. I have used it before, but it is $25.00 a can. I found the passanger side electrical connections harder than the drivers side. My drivers side only had on econnection and the passanger side had two. Plus the passanger side wires were much shorter on my truck. __________________ Reid

09-04-2007, 11:23 AM	#14
nd CA Founder: I'm back bitches!!! Joined: Mar 2007, #1047 Location: Greenville, SC Age: 26 Posts: 5,640 07 TRD Off-Road 4x4 debadged 2007 Double Cab Automatic V6 De badged, 5100's, Black Toyota Baja wheels	I was skeptical when i saw this thread but i have to admit i really like the look of it and it doens't look to hard to do. I'm glad this one was turned into a "sticky" __________________ I am so unappreciative...

09-13-2007, 04:28 AM	#15
Viper-2 Secret Agent Joined: Jul 2007, #2073 Posts: 504	Yeah I was skeptical too, but it looks real nice. I don't know if I would do it, but it still looks real good.

09-14-2007, 02:30 PM	#16
Jesse Member Joined: Oct 2006, #82 Posts: 83	Where can you get that leather. Is it really leather, or leather lookalike?

09-16-2007, 07:40 PM	#19
jhodge83 CA: Lone Event Attendee Joined: Apr 2007, #1432 Location: Fayetteville, NC/Sumter, SC Age: 25 Posts: 3,625 09 Timberland Mica DC 4X4 Sport 2009 Double Cab Automatic 4.0L seatbelt chime mod, fog lights on anytime mod, and a few others in the sig!	looks good. i'm thinking about getting some black/grey leather seat covers, so black leather arm rests would look great __________________ 2009 Timberland Mica DC SB TRD Sport 4x4 Tow w/ Hook Hitch, All Weather Mats, In-Channel Rain Guards, Bed Mat, Debadged, Black Low Profile/Low Width Tool Box, Hi Lift, Black/Grey Iggee Seat Covers, K&N 77 Series Intake, Cargo Bar, Cobra Ultra 19 CB w/ K40 Antenna and 5" PA Speaker, Painted Rims w/ Black Lugs, LT255/75/17 BFG MT's, AllproOffroad Sliders and Skid Plate, 3" EZ Lift w/ AAL and Diff Drop on the way....35% Tint, Tinted Tails and 3rd Brake, Pioneer AVIC-N1 DVD/NAV, Flat Black Vinyl Emblems

09-28-2007, 05:53 PM	#20
babrown0475 Junior Member Joined: Sep 2007, #2845 Location: Jacksonville, Fl Age: 33 Posts: 5 05 BSP X-Runner 2005 X-Runner Manual 4.0 v6 black headlight mod, debagged, sos lowering kit, K&N intake, Magna Flow cat back exhaust, Grill Craft black mesh grilles, full audio system with Pioneer 7" in- dash dvd player	That is lookin mighty fine. I do believe I'll be doin this!!

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
leather kit installed on 06 extra cab....	julesbchillin	2nd Gen. Tacomas	17	11-05-2007 09:15 PM
Crappy arm rests	reid	2nd Gen. Tacomas	18	09-02-2007 08:36 AM
Anyone actually get aftermarket leather seats?	TacoMaster	2nd Gen. Tacomas	15	08-02-2007 05:49 AM
Thinking of a Tacoma.. Question about Leather	jazzpunk67	2nd Gen. Tacomas	21	03-22-2007 07:26 AM

09-15-2007, 08:20 PM	#17
reid Senior Member Joined: May 2007, #1645 Location: Vancouver BC Canada Posts: 260 2007 V6 Access Cab 2007 Access Cab Manual V6 4.0L Magna Flow stainless cat-back, 3" Toytec Lift, 32" Mickey Thompsons	It is real leather. I buy my leather at a leather supply store here in Vancouver. You could probably pick some up from a fabric/sewing store or a furniture upholstery shop. __________________ Reid

09-16-2007, 06:58 PM	#18
tucsontoast Junior Member Joined: Feb 2007, #885 Location: Tucson, Az Posts: 25	Reid, All I have to say is "SUWEEEEEET!!!" The time you took to detail the photographs and outline the instructions is greatly appreciated. I'm definitely going to perform this mod on my "YOCA" cuz I work for a living, and this will definitely be easier to clean than the factory fabric. Thaanks Maaan!