1. Welcome to Tacoma World!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Tacoma discussion topics
    • Communicate privately with other Tacoma owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

Speedometer, ABS, and Emergency Brake light

Discussion in '2nd Gen. Tacomas (2005-2015)' started by dlumsdenuga, Jul 31, 2014.

  1. Jul 31, 2014 at 5:37 AM
    #1
    dlumsdenuga

    dlumsdenuga [OP] New Member

    Joined:
    Jul 31, 2014
    Member:
    #135102
    Messages:
    3
    Gender:
    Male
    So I am new to the forum and need some help with a problem. I did the DRL OEM mod last night and everything seemed to go well and worked afterwards. This morning when I started driving to work I realized that the speedometer didn't work at all and the ABS light and Emergency Brake light stay on. I'm not sure exactly what I could have done that would have messed those up, but could use any help or advise where to look. Thanks for any help in advance.
     
  2. Jul 31, 2014 at 9:49 AM
    #2
    dlumsdenuga

    dlumsdenuga [OP] New Member

    Joined:
    Jul 31, 2014
    Member:
    #135102
    Messages:
    3
    Gender:
    Male
  3. Jul 31, 2014 at 3:01 PM
    #3
    08TRDOFFROAD

    08TRDOFFROAD Well-Known Member

    Joined:
    Nov 4, 2008
    Member:
    #10482
    Messages:
    4,390
    Gender:
    Male
    First Name:
    Dan
    Vehicle:
    21' Tundra Platinum & 08' TRD Offroad DCSB 4x4
    Bilstein 5100's w/front's set at 1.75", TRD exhaust, Colormatched grill, Illuminated 4wd selector switch, BAMF Bolt on Sliders w/kickout.
    Check Ign1 no. 2 fuse behind the cubby near your left knee when you are seated in the drivers seat (It is a 10 Amp fuse, should be in the second row down of fuses on the far left hand side of the fuse block). You likely shorted something out and blew the fuse. Does the radio and AC blower work?
     
    Last edited: Jul 31, 2014
  4. Aug 4, 2014 at 12:20 PM
    #4
    08TRDOFFROAD

    08TRDOFFROAD Well-Known Member

    Joined:
    Nov 4, 2008
    Member:
    #10482
    Messages:
    4,390
    Gender:
    Male
    First Name:
    Dan
    Vehicle:
    21' Tundra Platinum & 08' TRD Offroad DCSB 4x4
    Bilstein 5100's w/front's set at 1.75", TRD exhaust, Colormatched grill, Illuminated 4wd selector switch, BAMF Bolt on Sliders w/kickout.
    Did you get your problem figured out?
     
  5. Aug 4, 2014 at 8:29 PM
    #5
    Nutzo333

    Nutzo333 FreakShow333

    Joined:
    Aug 11, 2012
    Member:
    #84550
    Messages:
    119
    Gender:
    Male
    First Name:
    Cory
    Canada
    Vehicle:
    Lifted 06 SR5
    6" Fabtech Lift, 315/70 r17 Duratracs, TRD Cold Air Intake MBRP stainless with duel side exit rear exhaust
    Hope its a fuse bud. For me, when the good ol ABS, CEL, and park brake light came on... was cause all four of my ABS sensors were cooked
     
  6. Aug 5, 2014 at 12:44 AM
    #6
    MadMatt

    MadMatt Member

    Joined:
    Jul 23, 2014
    Member:
    #134562
    Messages:
    6
    Gender:
    Male
    Vehicle:
    PreRunner SR5
    Switchback signals, led stop lights.
    How did all the wheel sensors get cooked? Seems a little odd...
     
  7. Aug 5, 2014 at 8:01 PM
    #7
    Nutzo333

    Nutzo333 FreakShow333

    Joined:
    Aug 11, 2012
    Member:
    #84550
    Messages:
    119
    Gender:
    Male
    First Name:
    Cory
    Canada
    Vehicle:
    Lifted 06 SR5
    6" Fabtech Lift, 315/70 r17 Duratracs, TRD Cold Air Intake MBRP stainless with duel side exit rear exhaust
    Lift kit did most of the work on them lol. Plus its an 06, milage racking up, sees a lot of bush time. They didnt all go at once. one by one over a few months.
     

Products Discussed in

To Top