LSC15's 95 Tacoma 4x4

Go Back   Tacoma World Forums > Tacoma Discussion > 2nd Gen. Tacomas

Notices

Removing Rear Door Handles

Reply
 
Thread Tools Search this Thread Display Modes
Old 02-13-2010, 09:15 PM   #1
BreezyTaco [OP] BreezyTaco is offline
Senior Member
BreezyTaco is one of the sharper tools in the shedBreezyTaco is one of the sharper tools in the shedBreezyTaco is one of the sharper tools in the shedBreezyTaco is one of the sharper tools in the shedBreezyTaco is one of the sharper tools in the shedBreezyTaco is one of the sharper tools in the shedBreezyTaco is one of the sharper tools in the shedBreezyTaco is one of the sharper tools in the shedBreezyTaco is one of the sharper tools in the shedBreezyTaco is one of the sharper tools in the shedBreezyTaco is one of the sharper tools in the shed
Navy:
Joined: Feb 2009, #13907
Location: Corpus Christi, TX
Gender: Male
Posts: 300
BreezyTaco's Tacoma Gallery
Removing Rear Door Handles

I just installed color matching door handles on the front two doors, and I am stumped on the rears. How do I do this? I saw the thread about removing the whole door, do I have to do that in order to get the crappy cheap black handle toyota put on here? Any advice quickly is greatly appreciated.


http://ncttora.com/fsm/05+/data/ilea...6ta/062009.pdf
  Reply With Quote
Old 02-14-2010, 12:09 AM   #2
BreezyTaco [OP] BreezyTaco is offline
Senior Member
BreezyTaco is one of the sharper tools in the shedBreezyTaco is one of the sharper tools in the shedBreezyTaco is one of the sharper tools in the shedBreezyTaco is one of the sharper tools in the shedBreezyTaco is one of the sharper tools in the shedBreezyTaco is one of the sharper tools in the shedBreezyTaco is one of the sharper tools in the shedBreezyTaco is one of the sharper tools in the shedBreezyTaco is one of the sharper tools in the shedBreezyTaco is one of the sharper tools in the shedBreezyTaco is one of the sharper tools in the shed
Navy:
Joined: Feb 2009, #13907
Location: Corpus Christi, TX
Gender: Male
Posts: 300
BreezyTaco's Tacoma Gallery
I just figured it out, and it is pretty easy...

You remove the door panel by unscrewing the screw by the inside handle and the arm rest.

Remove the window switch and D/C the plug

You carefully pry out the panel, starting at the bottom closest to the cab of the door, and work your way up.

Once the door panel is off you will see one screw holding the outside handle, unscrew that with a T-30 bit, next you will see a rubber piece hiding the screw to the window guide remove that, and with a 10mm socket unscrew the bolt, then unscrew the bolt above it by the window.

Remove the wires that are by the window slide, it is a round thing that you can D/C with your fingernail. Off to the side there are 3 bolts holding the lock mechanism remove those and the lock should fall down allowing access to the bolt holding the end of the handle or where you could stick a key in. Unscrew that and pop out the end of the handle, I used a screw driver in between the handle and the little rubber piece.

Slide out the gripping part of the handle and replace with the new ones. After all of that is done put everything back together. Hope this helps, and is my first little write up let me know if you have any questions.
  Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Similar Threads
Thread Thread Starter Forum Replies Last Post
Replacing rear door handles on double cab need help jeffcookie22 2nd Gen. Tacomas 10 05-30-2012 08:43 PM
Help removing rear door windows eccracer104 2nd Gen. Tacomas 4 10-02-2011 03:47 PM
me and ryanj attempted to install rear door handles on my truck Marioso 2nd Gen. Tacomas 24 02-23-2011 05:09 PM
05+ rear suspension hardware (ubolts), d-cab door handles, etc justinh Buy / Sell / Trade 4 03-19-2010 12:35 PM
Removing DC rear door panels machman 1st Gen. Tacomas 7 10-25-2009 08:17 PM


Copyright © 2014 Tacoma Forum. Tacoma World is not owned by, or affiliated with Toyota Motor Corporation.