Install dual amp on my regular cab-Warning , super slow

I'm a newbie in here and new with the car electronic, please help me to build the right one for it(Please, excuse my English)

Here is mine

JL AUDIO JX250/1 to run my 10" sub
JL Audio JX360/4 run my
Alpine SPR-17S and 6x9 infinitive kapa
















To remove the manual window crank handle



Remove the panel



Use the flat head screwdriver to pop the cover at the handle






Here the the door actual make it turn into power door lock



Remove the seat




And the back panel




Remove both screw for the seat-belt









Pop this one and remove screw to take off the panel next to seat belt




Complete take off the cover inside cabin



Bought this one on Amazon

 

Deadening the inside door with Stinger road kill



I just bought one box of Stinger Road Kill and not enough for the deadening so i have to use alternate route that use the Frost King Duct insulate from Lowes to run the outside door panel and the ceiling . Hope it help
















Put the ceiling back

 

Looking good, I am more of a fan of Dynamat but Stinger should do ok. What kind of box are you looking to do? Also, remember to run RCA cables and power cables on separate sides. Fuse your power cable and run a short ground to a clean point.

 

Here how i run the wire between door and cabin through the boot cover use the fiber glass rod and the wire puller




This one through the fire wall ,








Pull the power wire




my amp and the wiring kit






This kit have enough for me run 2 power wire from the battery to amp

My DIY router jig





First of, i use the writing paper and put the cooking oil on it so i can see through and put it on the door to trace the pattern of the speaker baffle using the pencil . Transfer it to 1/2" MDF and cut it. Because it a triangle shape want to make the circle inside the triangle shape, i use 60 degree ruler to make the perfect triangle .

Cut it with scroll saw




And grind it




And paint it

 

Thank you for your reply, i think about to build a box with my 6x9 infinitive kapa and 10" sub on it, any recommendation how to build it

And power cable i run it on the floor , RCA cables run on both side of panel

 

Run the RCA and speakers cable on both side and zip tie







Second power wire from the battery for my second amp




Bought this one from Haborfreight tool to make a flush











Connect speakers with solder and heat shrink







Speakers are in baffle and caulk with silicon caulk






Floor back in\




Can you guys tell me should i need to build the amp rack or just bolt it right to the floor ?

 

You won't get much out of 6x9s behind the seat, the highs and mids will be muffled and messy. From what you are doing I am guessing you are looking for loud and clear versus just heart stopping bass. A good set of 10s or a 12 in the back would do well. Add a component Kappa series in the door and maybe a set of kick panel pods and you will be set.

 

Since you have the skills I would mask a small amp rack, better to have them isolated from the floor

 

Is this hard to build it ? I measure the clearance from the floor to seat about 7" and cross beam in middle of cabin about 2" height , my amp thickness about 2" . Other question is if it bolt to the floor or amp rack is this hard to adjust it when need for tuning ?

Please, be advised

Thank you

 

If you go with just one 10 inch sub then you can make an amp rack/box combo for behind the seat and have a removable block to get to your tune settings. As long as you keep enough air flow for cooling then that would work well. I've never liked mounting amps under the seat except as a last resort.

 

My amp rack build








With brad nail



Drill the hole with drill press, not on the straight line newbie



Use rivet to bold down the amp rack



I'm cheap and find the fabric lay around garage and just put it on instead of vinyl over it







Dang man, mistake taken. I drill right on the RCA cable just bough from Sonic, that cost me $25 , i'm trying to solder every single wire together and heat shrink them all.




Please, help me. Is this safe to do that or just buy the new one. Like i said i kind of cheap or i just buy the RCA head only and solder it

I have 2 Monster home audio RCA cable laying around , i want to use it for amp but it too short .

Please, give me an advise

Thank you

 

Looking good!

 

just buy rca they are cheap. No need put amp rack. put amp under the seat

 

I agree!^^

 

To save $ i'm going to solder my rca together and heat shrink every single wire





Amp rack build











But when i put the amp and crossover on it and put the seat back on, it too tall for it and not fit so i have to take the 1 inch off of the amp rack

The amp are in place




Tuning my amp ,

Gain Setting Equation
Voltage of the output = sqrt(RMS Power X impedance of the speaker)






Seat back in




First amp



to drive my 12" pioneer my brother gave it to me that save me some $, but the box are junk and none carpet , i have to fix it up and carpet it

Second amp drive my component speakers



My sub



Need to carpet




Go to Wal-mart http://www.walmart.com/ip/Remington-Industries-Carpet-Replacement-Gray/15524369

and buy this ready to carpet, anyone know how to carpet, please share.

 

Finished