I need help wiring a remote start

ho_ho14 · 05-11-2008, 08:28 PM

I can't seem to find the IMO and IMI wires I know they are the lt green/black and the blue/white wire on the 2ed clip on the ECM but I can't find it. Any informatin would relly help

dsds · 05-12-2008, 12:14 AM

The wiring diagram for the immobilizer bypass usually shows the various connectors including one for tacoma. Go to the website for the immobilizer and chances are you'll find a PDF file or something that shows the connector you're looking for.

It gets confusing depending if you're looking at the female or male side.
Those two wires are hard to get at with all the action at the ECM.
Keep looking because they are there. They are very light gauge wires.

Here is the one I used and it shows the connector that you need to look for:

http://www.bypasskit.com/getdocument...documentid=556

Tacoma is pins 15 (lt grn/blk) and 16 (lt blue/wht) on connector E7. The above file shows a diagram of that connector a page or two down (also read Tech Notes at bottom on file since it is about the Tacoma).

I used a soldering iron to melt the insulation and then solder the wires.
After that I snipped the IMI pin 16 wire.

A good site is the12volt.com
Thats where I went for help with my RS (Valet).

05-11-2008, 08:28 PM	#1
ho_ho14 Junior Member Joined: May 2008, #6523 Location: Kula Hawaii Posts: 1	I need help wiring a remote start I can't seem to find the IMO and IMI wires I know they are the lt green/black and the blue/white wire on the 2ed clip on the ECM but I can't find it. Any informatin would relly help

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Remote Start	stucksucksnayota	1st Gen. Tacomas	5	04-22-2008 05:13 PM
2001 Tacoma Remote start help	hoxie08	1st Gen. Tacomas	2	03-13-2008 02:02 PM
remote start	dsds	2nd Gen. Tacomas	8	03-08-2008 08:54 PM
Remote start	Bfmco7	2nd Gen. Tacomas	16	01-10-2008 10:07 PM
Remote Start DrDetail	wildman	2nd Gen. Tacomas	0	12-12-2007 04:30 PM

05-12-2008, 12:14 AM	#2
dsds Member Joined: Nov 2007, #3433 Location: Calgary AB Posts: 99 2008 DC TRD Sport - Black Sand Pearl 2008 Double Cab Automatic TacomaWorld sticker, DRL mod, running boards, roof rack, remote start / security alarm, marker/turn signal mod, map light with dome light mod, TRD seat covers, rear spring TSB	The wiring diagram for the immobilizer bypass usually shows the various connectors including one for tacoma. Go to the website for the immobilizer and chances are you'll find a PDF file or something that shows the connector you're looking for. It gets confusing depending if you're looking at the female or male side. Those two wires are hard to get at with all the action at the ECM. Keep looking because they are there. They are very light gauge wires. Here is the one I used and it shows the connector that you need to look for: http://www.bypasskit.com/getdocument...documentid=556 Tacoma is pins 15 (lt grn/blk) and 16 (lt blue/wht) on connector E7. The above file shows a diagram of that connector a page or two down (also read Tech Notes at bottom on file since it is about the Tacoma). I used a soldering iron to melt the insulation and then solder the wires. After that I snipped the IMI pin 16 wire. A good site is the12volt.com Thats where I went for help with my RS (Valet).