Sandman614's #expoenough Build

It's beauriful

 

I gotta wire them to a switch still. I'll get that, bed lights and rock lights later.

 

Will be replacing LCA bushings and bolts soon.
http://youtu.be/JZ5BMfkuHlM

Moog greasable bolts, need 2 kits

$44 K100128 Alignment Caster/Camber Kit for Toyota Tacoma

K100128
Whiteline bushing kit W53312

 

Never thought about keeping my light saber there... Thanks for the idea

 

Wiring up bed lights and putting hood lights to the switch.

 

ITs about time! That stuff had only been in your garage for a year lol

 

Found out my trailer harness wasn't working for the right turn signal, pulled it out to rule out shorts. It had a constant power wire straight to the battery and the new ones don't need it so I added a Fuse block! Bed lights, USB and 12v outlets, the list is endless..

 

I like the install done by truckwater.com. The Hidden tank in the passenger fender to help offset fuel, the fill cap in the bedside or cubby, and the output line in the cubby hole. I'd like to carry 5-10 gallons and keep this water clean and potable. Skygear, I will be asking you a few questions.

$28 Seaflo 12V DC 1.2 GPM 35 PSI 21-Series Diaphragm Water Pressure Pump for Caravan/RV/Boat/Marine

Reliance Products Jumbo-Tainer 7 Gallon Jerry Can Style Rigid Water Container, Blue, 15.5" x 7.3" x 21.8"

Maybe use some water rated pvc pipe. I'm thinking a multi pipe setup.

=====3-4ft===' '=
I I
=,,====3-4ft=====

http://www.handymath.com/cgi-bin/cylinder.cgi

 

http://forum.ih8mud.com/threads/anyone-use-6-pvc-pipe-as-water-storage-tanks.109202/

 

My wife would always be willing to go camping if i had a shower on my truck haha

 

Voz would be more comfortable too!

 

And in the final hour, let there be light.

 

Changed the passenger inner CV boot.. We'll see how long it lasts.

 

Lights looked good the other night!

 

For my occasional p0171 code

http://youtu.be/Hmt_LNJ9GkI

 

According to the freeze frame data this is an under load lean condition. I have cleaned and replaced the MAF sensor with a known working one with no changes.

Freeze frame data from p0171-174
Fuel Status = 0 byte
Engine Load = 92.157 %
Engine Coolant Temperature = 195.8 °F
Fuel Trim Bank 1 Short Term = 0 %
Fuel Trim Bank 1 Long Term = 36.719 %
Fuel Trim Bank 2 Short Term = 0 %
Fuel Trim Bank 2 Long Term = 33.594 %
Engine RPM = 2,101.5 rpm
Speed (OBD) = 69.594 mph
Timing Advance = 17.5 °
Intake Air Temperature = 86 °F
Mass Air Flow Rate = 492.754 cfm
Throttle Position(Manifold) = 38.431 %
Run time since engine start = 1,067 s
O2 Sensor1 Equivalence Ratio = 0.995
O2 Sensor5 Equivalence Ratio = 1.003
Distance travelled since codes cleared = 164.042 miles
Barometric pressure (from vehicle) = 13.779 psi
O2 Sensor1 Equivalence Ratio(alternate) = 0.995
Catalyst Temperature (Bank 1,Sensor 1) = 1,503.68 °F
Catalyst Temperature (Bank 2,Sensor 1) = 1,503.68 °F
Catalyst Temperature (Bank 1,Sensor 2) = 1,355.54 °F
Catalyst Temperature (Bank 2,Sensor 2) = 1,355.54 °F
Voltage (Control Module) = 13.535 V
Engine Load(Absolute) = 73.725 %
Commanded Equivalence Ratio(lambda) = 0.987
Relative Throttle Position = 21.176 %
Absolute Throttle Position B = 76.078 %
Accelerator PedalPosition D = 38.431 %
Accelerator PedalPosition E = 54.118 %

http://youtu.be/nYN-RoFVwAA

 

Smh

 

Before cleaning MAF:


after cleaning MAF (ltft is high because I made a vacuum leak, for testing purposes):

 

Flyzeye V2W installed! Blue halos/blue primary/white secondary. I won this in the raffle at the Big Dogs Offroad/Stephens Toyota meet!! Thank you Flyzeye, I enjoyed meeting you last year! Before:

After, White :


After, Blue:

 

Center console organizer, aka bar caddy for napkins and salt/pepper and straws. It's a very tight fit. I'll probably cut off the two driver side pieces so I can take it out.