Sliders, Skid Plates, Bumpers, OEM Suspension...TRD of course.

Never installed BAMF DCSB with kick out bolt on sliders.
These were ordered for a 2012 but understand they will fit all 2nd generations dc and ac. Please verify yourself.
I ordered these on TW 2.5 years ago on TW from the Man Jerry his damn self. They were never installed as I was unable to drive following an accident. I wasnt able to drive for a couple years and these sat in my shop collecting dust. I did prime them and used some thin bed liner spray on them(can't remember what). They are in fantastic condition and have a few nicks on the finish from moving them from one side to the other a few times.

I have the bolts, nuts and the carbide drill bit he sent to drill the frame with.
The sliders $300, kickout +$40, bolt on +130 drill bit and shipping +125. My cost $595.00.
$300.00 + Fastenal shipping on your dime. SOLD


Relentless engine and mid/transmission skid plates
Same storyline as above. Eric is also a fantastic fabricator and a great guy.
The engine skid was $202.00 and the mid/trans skid was $155.00 + 100.00 in shipping(wasn't far to ship).
I also primed these but have a few needed touch up spots from moving them around. Rustoleum, invest in it if you offroad.
$225.00 and Fastenal shipping on your dime. Will not split and these were not sent with hardware. SOLD







The following items were removed off my 2015 dcsb at exactly 174 road miles. What you see in the photos is what you will receive -

Rear Bumper with hitch, no hardware - $150.00 + shipping - no split


4 Leaf! Leaf Springs and u bolts(missing nut and washer for one u bolt stud) - $100.00 + shipping
SOLD



MGM front bumper without fogs with crash bar - $125.00 + shipping



Front and rear Bilstein Shocks.....TRD(Dick) - $175.00 + shipping


UCA's - $50.00 + shipping.
Note - I also have another set off a 2011 roughly same mileage if interested.



I would also be interested in trading anything firearms related and or strippers. I am happy to take additional photos if necessary. Thank you for looking.

 

Pm sent.

 

pm sent as well

 

PMd

 

PM sent about leafs, I would probably be interested in the UCA's as well...

 

I have close to 20 PM's. I have PM'd a few back. As mentioned I will be shipping through Fastenal and will be checking cost to your home zip. I will be getting prices for the next day or 2. Please be patient as I have to load parts up, drive a good distance, get quote, drive home and pm for verification that you're ok with quote and hope you pay.
I appreciate you all looking.

 

thanks man!

 

Bump. Serious drool factor for those skids, but shipping would kill it for me, I'm broke . GLWS

 

Where at in Idaho are you located?

 

twin falls. basically boise. southern idaho.

 

hmmm. Will keep an eye on this. If nobody jumps on it really quick I may have to drive up there and pick some of this up.

 

i didnt just jump.....i fell on the sliders.....wife convinced they are steps and she drives the struggle bus at 5'3'' about getting in the truck.

 

If you still have the skids around Christmas I would definitely be interested in getting them.

I will be in Tamarack, ID then.

If you were to ship them via Fastenal how much would it be to Tacoma, WA 98335?

 

Are the sliders gone?

 

They are at Fastenal awaiting a ship quote for a member.

 

You should post up the quote so we can have a rough estimate

 

yes and I'm interested in the sliders too!

 

dude great deals you got going!

 

Sent you a PM. I am interested in the sliders and I actually think I want the skids too. I have a buddy in Boise that could meet you half way to pick up. Let me know in the PM (I didnt mention the skids in the PM but i am interested).