LSC15's 95 Tacoma 4x4

Go Back   Tacoma World Forums > Tacoma Garage > Audio & Video

Notices

What pins does +/- go to on non-JBL radio?

Reply
 
Thread Tools Search this Thread Display Modes
Old 12-01-2011, 11:23 AM   #1
Whitster [OP] Whitster is offline
Senior Member
Whitster has much to be proud ofWhitster has much to be proud ofWhitster has much to be proud ofWhitster has much to be proud ofWhitster has much to be proud ofWhitster has much to be proud ofWhitster has much to be proud ofWhitster has much to be proud ofWhitster has much to be proud of
 
Whitster's Avatar
Name: Whit
Joined: Sep 2011, #63656
Location: Golden, CO
Gender: Dude
Posts: 306
Whitster's Tacoma Gallery
What pins does +/- go to on non-JBL radio?

I installed a Kenwood in-dash unit on my '09 AC. Finally got the AXXESS steering wheel control and backup camera running with help from other posts on this great Forum.

Anyway, after all was done I discovered that I'd forgotten to eject the 6 CD's that were still in the OEM head unit now sitting on the bench...DUH!!!

I removed the top cover and the CD-drive mechanics don't look like anything that would readily accommodate physical removal without screwing up the alignment.

There are four jacks on the back of the HU. The two on the right have bigger conductors so I'm assuming the power might come to it in those somewhere. (of course nothing is marked)

There is a 6-conductor jack and a 10-conductor jack.

Could anyone with a schematic tell me which pins, and polarity, I need to apply 12 V to?
I'm hoping I can apply the power and press the eject button to extract the CD's.

Thanks,

Whit
  Reply With Quote
Old 12-03-2011, 10:58 AM   #2
Whitster [OP] Whitster is offline
Senior Member
Whitster has much to be proud ofWhitster has much to be proud ofWhitster has much to be proud ofWhitster has much to be proud ofWhitster has much to be proud ofWhitster has much to be proud ofWhitster has much to be proud ofWhitster has much to be proud ofWhitster has much to be proud of
 
Whitster's Avatar
Name: Whit
Joined: Sep 2011, #63656
Location: Golden, CO
Gender: Dude
Posts: 306
Whitster's Tacoma Gallery
P.S.

Just for future information in case anyone else needs the info...

Looking from the rear...the power connections are made to the far right connector, R1, a 10-pin connector. Six across the top and 2 plus 2 on the bottom.

Take a flashlight and look carefully inside the jack, the pins are numbered in the white insulating body of the jack.

Connect negative to pin 7.

Connect positive to pins 3 & 4. Upon connecting the power you'll hear the CD changer cycle a couple times and the amber display will illuminate. After that just push the CD eject button to eject the CD's.

Thanks again to Caribe for schematic.

I'd include the schematic but won't fit with the website's 100K attachment limit.

Whit
  Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Similar Threads
Thread Thread Starter Forum Replies Last Post
JBL radio cweeks1934 Buy / Sell / Trade - Other 6 11-22-2010 02:55 PM
Does the JBL Sat Radio also do local HD Radio? Smimo 2nd Gen. Tacomas 3 10-21-2010 09:26 PM
JBL Sat Radio jonboy 2nd Gen. Tacomas 0 02-15-2010 05:15 PM
JBL Tacoma Radio pb4ugotobed Buy / Sell / Trade 5 01-20-2010 05:47 PM
JBL radio jabrackin 2nd Gen. Tacomas 3 09-04-2009 04:36 AM


Copyright © 2014 Tacoma Forum. Tacoma World is not owned by, or affiliated with Toyota Motor Corporation.