BAMF Rock sliders "most" Trucks

Code:

B.A.M.F rock sliders

Specs
Built from 1.75" .120 wall HREW or DOM bent, notched and fully welded to a 2x2 square tube with square legs and 3/16th frame plates and gussets. The sliders have a 1.5" taper towards the rear of the truck to aid in pushing the truck away from obstacles. With a added kick out (highly recommended for longer wheel base trucks) they will stick out 3.5" past the slider.

Some people ask why I use a square tube here is your answer
2 x 2 .120 square has nearly the same MOI (Moment of Inertia) as the 2 x 250 round, and is 35% lighter still (or 25% stronger and less than half the weight of the 1.75 x .5 round)


OD_ / ID_ = ....MOI........ Weight
.......... round square ,round square
1.5 /.120 = .125 , .212 , 1.77 , 2.25
1.5 /.188 = .170 , .289 , 2.63 , 3.35
1.5 /.250 = .199 , .339 , 3.34 , 4.11
1.5 /.375 = .233 , .... , 4.51
1.5 /.500 = .245 , .... , 5.34

1.75/.120 = .205 , .348 , 2.09
1.75/.188 = .285 , .484 , 3.14
1.75/.250 = .341 , ....., 4.01
1.75/.375 = .411 , .... , 5.51
1.75/.500 = .445 , .... , 6.68

2.0 /.120 = .314 , .534 , 2.41 , 3.05
2.0 /.188 = .444 , .754 , 3.64 , 4.32
2.0 /.250 = .537 , .911 , 4.67 , 5.41
2.0 /.375 = .666 , .... , 6.51
2.0 /.500 = .736 , .... , 8.01

2.25/.120 = .457 , .... , 2.73
2.25/.250 = .798 , .... , 5.34
2.25/.375 =1.01 , ..... , 7.51
2.25/.500 =1.138 , .... , 9.35

2.5 /.120 = .637 , .... , 3.05
2.5 /.250 =1.132 , .... , 6.01
2.5 /.375 =1.457 , .... , 8.51
2.5 /.500 =1.669 , .... ,10.68




Ordering can be done by going HERE and place your order

 

Nice!!!

 

nice

 

nice

 

I continue to like what I'm seeing coming out of your shop.

 

I should jack it up on one side by the sliders and take a pic Too bad I don't think my jack is tall enough. We'll figure something out this weekend.... providing Toyota Financial doesn't screw me over more.

 

Whats the pricing for these things?

 

W
A
H
N
T

 

Yay for hybrid design. That is the correct way to do sliders.

 

x2!!!

 

Here is a set of non kick outs im working on for a member. They get progressively wider towards the back by about 1.5"

Don't mind my remodeling in the back ground

 

welds/sliders look great!

 

Jerry, got to see your sliders on Brian's truck. They are sick! Nice work man! Wondering if you'd be willing to do a set for my 09 DCSB?

 

Looks to be an awesome job!

 

Looks good!

I have a general question I've been wanting to ask a fabricator about sliders. With the kick-outs, why the 2-part tubing? How come one piece starts at the front and ties back to the square tube, then a second piece makes the back kick-out, why not one single, continuous piece braced back to the square tubing every 12" or so. Just curious, I'm far from a fabricator, just a wondering mind!

 

Thanks man and yes I'm willing to do a set for you I'll do a set for everyone

Looks mainly I didn't like the look of one tube for the kick out sliders so I went this route. Non kick out sliders are one piece.

 

Sweet! Sent you a PM!

 

SICK!

 

Thanks