LSC15's 95 Tacoma 4x4

Go Back   Tacoma World Forums > Tacoma Garage > Lighting

Notices

Electrical Clips for Corner Lights

Reply
 
Thread Tools Search this Thread Display Modes
Old 07-03-2012, 06:28 PM   #1
Pluffmud13 [OP] Pluffmud13 is offline
Member
Pluffmud13 is on a distinguished road
Name: York
Joined: Jun 2011, #57766
Location: Clemson/Charleston
Gender: Male
Posts: 31
Pluffmud13's Tacoma Gallery
Electrical Clips for Corner Lights

Anyone know how to detact the metal clips from the plastic housing (located on the plastic inside the red rubber), so they can be moved from the corner lights to the turn signal. They seem similar to the ones found in the fuse box but it could not figure out how to get them out.

  Reply With Quote
Old 07-03-2012, 10:32 PM   #2
Lurker No More
caribe makaira is one of the sharper tools in the shedcaribe makaira is one of the sharper tools in the shedcaribe makaira is one of the sharper tools in the shedcaribe makaira is one of the sharper tools in the shedcaribe makaira is one of the sharper tools in the shedcaribe makaira is one of the sharper tools in the shedcaribe makaira is one of the sharper tools in the shedcaribe makaira is one of the sharper tools in the shedcaribe makaira is one of the sharper tools in the shedcaribe makaira is one of the sharper tools in the shedcaribe makaira is one of the sharper tools in the shed
 
caribe makaira's Avatar
Navy: CAG11 & VAW-117 AME2
Joined: Feb 2011, #51121
Location: Caribbean, Puerto Rico
Gender: Male
Posts: 426
caribe makaira's Tacoma Gallery
See the white rectangle, it needs to be pulled out (not entirely). It'a a lock. After that, the connectors are held in place by a tang which needs to be pulled down at the same time you tug on the wire to remove the connector from the housing/plug.
  Reply With Quote
Old 07-04-2012, 06:07 AM   #3
Pluffmud13 [OP] Pluffmud13 is offline
Member
Pluffmud13 is on a distinguished road
Name: York
Joined: Jun 2011, #57766
Location: Clemson/Charleston
Gender: Male
Posts: 31
Pluffmud13's Tacoma Gallery
Quote:
Originally Posted by caribe makaira View Post
See the white rectangle, it needs to be pulled out (not entirely). It'a a lock. After that, the connectors are held in place by a tang which needs to be pulled down at the same time you tug on the wire to remove the connector from the housing/plug.
What is this tang you speak of? The rubber stopper holding the wire in there? And to get the connector to release from the housing does something small need to be pressed inside it and on which side, the side of the white rectangle or inside the connector? Thanks man.
  Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Similar Threads
Thread Thread Starter Forum Replies Last Post
Corner Lights holtuscg 1st Gen. Tacomas 1 06-01-2012 01:43 PM
Corner lights? Oat 1st Gen. Tacomas 11 01-16-2012 11:30 PM
Corner Marker Electrical Connector KingToaster 1st Gen. Tacomas 2 08-19-2011 11:49 AM
Tail Lights Blinker On with Headlight Corner Bulb Lights Drunknsloth Lighting 7 03-12-2011 09:56 AM
Tail Lights and corner lights for a 2000 4wd WANTED SchrammMan74 Buy / Sell / Trade 1 10-12-2007 07:42 AM


Copyright © 2014 Tacoma Forum. Tacoma World is not owned by, or affiliated with Toyota Motor Corporation.