Speedytech7
Joined:
Feb 20, 2014
Messages:
58,091
Likes Received:
78,955
Trophy Points:
0
Media:
1
Albums:
2
Gender:
Male
Location:
FCQM+VG Cheney, Washington

Speedytech7

Toyota Cult Ombudsman, Male, from FCQM+VG Cheney, Washington

“I can't go to hell. I'm all out of vacation days.” Jan 31, 2024

Speedytech7 was last seen:
Viewing thread 1st Gen Lunchtable Thread - General Discussion, Jul 22, 2025 at 12:19 PM
    1. TunaTaco4lyfe
      TunaTaco4lyfe
      May 10, 2025
    2. 97taco_verde
      97taco_verde
      Do you have the 96' repair manual pdf?
      Feb 26, 2024
    3. beaverdamland
      beaverdamland
      Really digging the wheels on your 80 series, mind sharing what they are?
      Feb 7, 2024
      2. Speedytech7
        Speedytech7
        I've only ever had the stock 80 series Wheels on my Land cruiser. They happen to be really good fitment for tacomas too and they're one of Toyota's only factory 8-in wide wheels for six lug
        Feb 7, 2024
    4. Speedytech7
      Speedytech7
      “I can't go to hell. I'm all out of vacation days.”
      Jan 31, 2024
      1. _-IV-_ likes this.
    5. Yakuza23
      Yakuza23
      Hey, I was reading a thread from a couple years ago regarding clusters with tachometers and you posted you had a 95-97 4cyl cluster. I know it’s a long shot but I was just wondering if you still had it and would want to sell it?
      Aug 19, 2022
    6. shuttleboi
      shuttleboi
      Hey speedytech I saw a picture of your tacoma on a thread and was wondering if you have a build forum set up for it? If so I would love to look at it or if not do you have any pictures to post of it throughout the years that you have had it?
      Feb 18, 2022
      2. Speedytech7
        Speedytech7
        I did make a build thread recently for it
        Jan 4, 2023
    7. Rutted_Taco
      Rutted_Taco
      Hey, relatively new to TW but looking through older posts it seems you have some experience with 6112 bilsteins and preferred spring rate on a first gen? I'm looking to get around 1" of lift and add an ARB bumper in the future, should I be looking for a heavier spring rate than 600lb?
      Jul 28, 2020
      2. Pops101056
        Pops101056
        I went with the 650# spring with the ARB deluxe bumper on 6112/5160 set up and I’d say after about 6 months of use one inch is what I ended up with (replacing 100,000 mile original factory parts..)
        I also added the “regular” Old man emu leaf pack..
        it was exactly what I was trying to achieve... a little lift and a vastly improved ride and handling on ranch/off road driving!
        Jul 28, 2020
    8. Stormintaco
      Stormintaco
      Hey bud I’m just reading through posts pulling my hair out trying to find where to connect my FPR on my 3RZ supercharger to reference boost. Just finished it today and wondering if you could help. Thanks!
      Dec 10, 2018
      1. Speedytech7 likes this.
      2. Speedytech7
        Speedytech7
        Sure I'll PM a pic of how mine is setup. I have mine boost referenced so it sees engine vacuum and boost so it properly lowers fuel pressure and raises it.
        Dec 10, 2018
    9. RichieR1ch
      RichieR1ch
      I saw a post on a WTB thread where you were offering to sale 16in 4.5bs SCS F5 Gray Wheels...can I get details if still available?
      Dec 9, 2018
      2. Speedytech7
        Speedytech7
        Sorry, I sold them a while back. Good luck finding a set. You could always PM @SCSPerformance about getting blem f5s, Vin is super picky and most of them still look perfect to normal eyes haha
        Dec 9, 2018
    10. sd_N
      sd_N
      Can u help me speedytech7? I started a thread in the 1st gen tacoma section, if you'd like to read it there and reply or I can PM you. Thanks
      Sep 18, 2018
      1. Speedytech7 likes this.
    11. xrdad
      xrdad
      Thank you!
      Jul 25, 2018
      1. Speedytech7 likes this.
    12. xrdad
      xrdad
      Annnd... I may have found it... in the wayback machine :)
      Downloading something now, will let you know if it works.
      Jul 25, 2018
      1. Speedytech7 likes this.
      2. Speedytech7
        Speedytech7
        Jul 25, 2018
    13. xrdad
      xrdad
      Hi Speedytech7.
      Sorry to bug. Just got a '95 Tacoma and am in at the beginning of repairing it. I was looking for a s/manual online, found one of your post and was hoping you would share a copy with me?
      Thanks in advance, looking forward to hearing from you.
      Ivan
      mustbtime@gmail.com
      Jul 25, 2018
    14. tokecoma
      tokecoma
      Hello, I would like to by your 4.30 gears for first gen taco.
      Feb 27, 2018
      1. Speedytech7 likes this.
  • Loading...

  • About

    Gender:
    Male
    Location:
    FCQM+VG Cheney, Washington
    Vehicle One-Line Description:
    96 Turbo Taco V6 405WHP & 482lbft
    Vehicle Modifications:
    It's less Tacoma and more mod

    Interact

    Content:

    Signature

    [​IMG] [​IMG] Now with extra build thread™
  • Loading...
  • Loading...
To Top