1. Welcome to Tacoma World!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Tacoma discussion topics
    • Communicate privately with other Tacoma owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

D Rings.

Discussion in 'Off-Topic Discussion' started by travis9287, Aug 14, 2011.

  1. Aug 14, 2011 at 8:37 PM
    #1
    travis9287

    travis9287 [OP] Well-Known Member

    Joined:
    Jun 1, 2010
    Member:
    #38150
    Messages:
    1,682
    Gender:
    Male
    First Name:
    Travis
    Tuscaloosa,AL
    Vehicle:
    2003 Tacoma, 2006 GX470, 2000 Jeep TJ, 1985 C10
    a lot lol
    I Got 4 Weld or Bolt On D Rings, i was wanting to put them on the front for towing points but i still have the stock bumper and valence, has anyone mounted them with a stock bumper? if so i would like to see some pics!
     
  2. Aug 14, 2011 at 9:15 PM
    #2
    4x4Runner

    4x4Runner Sam’s gone, man. Moderator

    Joined:
    Sep 9, 2006
    Member:
    #7
    Messages:
    25,222
    Gender:
    Male
    First Name:
    Drunken Sailor
    Not north, not south, not west, mostly east
    Vehicle:
    1WD
    nuttin fancy
    I would not attach them to the stock bumper if you are going to use them for recovery.
     
  3. Aug 14, 2011 at 9:17 PM
    #3
    travis9287

    travis9287 [OP] Well-Known Member

    Joined:
    Jun 1, 2010
    Member:
    #38150
    Messages:
    1,682
    Gender:
    Male
    First Name:
    Travis
    Tuscaloosa,AL
    Vehicle:
    2003 Tacoma, 2006 GX470, 2000 Jeep TJ, 1985 C10
    a lot lol
    Well I wasn't talking about to the actual bumper itself. More like if some has done something with some angle iron and attached them to that but kept the stock bumper on also.
     
  4. Aug 14, 2011 at 9:19 PM
    #4
    Darth Tater

    Darth Tater If I can't get you out, neither can anyone else.

    Joined:
    Jun 14, 2011
    Member:
    #58273
    Messages:
    200
    Gender:
    Male
    First Name:
    Marlin
    Las Vegas, Nevada!!
    Vehicle:
    06 4X4 Taco, ARB, DBL Cab
    ARB,WARN 8K (F&R), 3" lift, Snugtop, tube steps, factory roof rack, Dick Cepeks,
    You might be able to bbb attach them to the frame, but the stock bumper is aluminum and probably wont hold up too well.
     
  5. Aug 14, 2011 at 9:30 PM
    #5
    TacoNut

    TacoNut IgnoringChrisWatchingEdLi veVicariouslyThroughMJP2

    Joined:
    Mar 29, 2008
    Member:
    #5597
    Messages:
    5,237
    Gender:
    Male
    First Name:
    Adam
    Denver, Co
    Vehicle:
    16 TRD OR DCSB Quicksand
    X2
    A better, easier route is to get something that attaches to your hitch receiver.
     
  6. Aug 15, 2011 at 7:21 AM
    #6
    travis9287

    travis9287 [OP] Well-Known Member

    Joined:
    Jun 1, 2010
    Member:
    #38150
    Messages:
    1,682
    Gender:
    Male
    First Name:
    Travis
    Tuscaloosa,AL
    Vehicle:
    2003 Tacoma, 2006 GX470, 2000 Jeep TJ, 1985 C10
    a lot lol
    I have one in my hitch. I was just wanting something in the front. I may just mount them in the bed for extra tie downs.
     
  7. Aug 15, 2011 at 8:21 AM
    #7
    TacoNut

    TacoNut IgnoringChrisWatchingEdLi veVicariouslyThroughMJP2

    Joined:
    Mar 29, 2008
    Member:
    #5597
    Messages:
    5,237
    Gender:
    Male
    First Name:
    Adam
    Denver, Co
    Vehicle:
    16 TRD OR DCSB Quicksand
    ahh my fault... reading is hard. :p
     

Products Discussed in

To Top