Calling all Toyota owners in the Lynchburg and Charlottesville and surrounding areas!

Replace your u-bolts while you're in there.

 

Okay. Anything else? Is a diff drop necessary? I have the ADD. Will I need any new bolts or anything? Bumpstops?

 

Change of plan now I'm going to go with wheelersoffroad.com because they have a big variety as great prices as well. I'm think eithe a nice set off OME shocks and coilovers and rear shocks or a nice set billies just depends on how much money I get back if I get enough I might go with a nice set of long travel icons or fox.

Taylor it depends on how much lift your going with if your going with 3" or more or maybe 2.5" you will probably have to go with the diff drop and just depends on what setup you go with just depends some kits come with hardware some don't you may need center pins and u-bolts and whatever else.

 

What's your plan on the rear?

And ugh, I don't have the money for a diff drop. Nevermind. Guess it's just spacer plates?

I wish there was a list of the bolts and bushings I'll need to replace.

So, billies up front set all the way up with stock springs and diff drop. 2.5 inches of lift.

In the rear, allpro leaves and shocks, extended brake lines, new u bolts. 3 inches of lift.

I wonder how awkward that rake would look? Would the rear settle down more than the front?

 

2" AAL and either billies or OME's. I think you'll be ok and of you need anymore let me know or pm me.

 

Blacksburg count?

 

Yea man of course happy to have your interest. Is tht where you live or are you just at school?

On another note 4 decals down 6 more to go. Claim em if you want them.

 

School, I'm from yorktown

 

Don't waste your money on a diff drop, at least on the 2nd gens their not worth it. Don't you 1st gen guys need a BPV bracket when lifting?

 

Ok cool thanks for the interest and keep an eye on this thread. We are planning an meet and eat and hopefully another trail ride here in the very near future.

 

Nice, make sure you get down in between the hitch and plate area. I don't think I did mine very well and am now concerned with all this salt on the road.

 

I think I'm going to drill a couple of holes in the bottom there as well to drain any water, just seems like a rust breeding ground back in there.

 

Sweet! Chopping sounds a lot more fun than moving.

 

http://bilsteinlifts.com/shop/95-04...table-lift-kit-with-5100-shocks-95-04-tacoma/
Taylor check this website out see if you find anything you like.

 

damn, wish i would have seen that website before i ordered my lift. I spent a couple hundred more than that by getting everything separately

 

Yea I know I found this alittle bit ago. It's awesome that we have so many different parts available to us.

 

I think and hope I finally found what I'm going to get and here is the winner so far:

Bilstein 5100 Front adjustable shock x 2
Bilstein 5100 Rear shock x 2
Deaver 2" AAL
Eibach Front Coils
Diff Drop Kit
Brake Proportioning Valve Bracket Kit (for 2" lift or more)

 

I can't use websites like that because I need new leaves entirely. Not AALs.

Also, I've heard anything about a new BPV. Where is that even located?

 

A-ha!

How about

http://bilsteinlifts.com/shop/95-04...ble-front-shocks-for-1995-2004-toyota-tacoma/

and

http://toyteclifts.3dcartstores.com/Old-Man-Emu-rear-springs_p_144.html

and then I can pick up the new ubolts, leave pin, brake line, and bushings all in the same order! That should give me the correct rake too!

 

anyone else get in on the ultragauge group buy? http://www.tacomaworld.com/forum/group-buys/312530-ultragauge-group-buy.html