LSC15's 95 Tacoma 4x4

Go Back   Tacoma World Forums > Tacoma Garage > Suspension

Notices

Ubolt Flip Kit questions

Reply
 
Thread Tools Search this Thread Display Modes
Old 04-14-2012, 10:47 AM   #1
mjm540ii [OP] mjm540ii is offline
Ding Dang Dee
mjm540ii is one of the sharper tools in the shedmjm540ii is one of the sharper tools in the shedmjm540ii is one of the sharper tools in the shedmjm540ii is one of the sharper tools in the shedmjm540ii is one of the sharper tools in the shedmjm540ii is one of the sharper tools in the shedmjm540ii is one of the sharper tools in the shedmjm540ii is one of the sharper tools in the shedmjm540ii is one of the sharper tools in the shedmjm540ii is one of the sharper tools in the shedmjm540ii is one of the sharper tools in the shed
 
mjm540ii's Avatar
Name: Mike
Joined: Apr 2011, #54457
Location: Oxford, PA
Age: 26
Gender: Male
Posts: 731
mjm540ii's Tacoma Gallery
Ubolt Flip Kit questions

Bought the All Pro ubolt flip kit, and I want to install it today. I was wondering, do I even need to jack anything up (Jackstands, rear axle, etc) since the leafs sit on top of the axle? Also, apparently the nuts all pro gives you are some fancy lock nuts that are a PITA to tighten. I was just wondering the best way/ any suggestions to go about getting them tight. Finally, Is there a write up on this? Thinking about doing one...
  Reply With Quote
Old 04-14-2012, 01:14 PM   #2
mjm540ii [OP] mjm540ii is offline
Ding Dang Dee
mjm540ii is one of the sharper tools in the shedmjm540ii is one of the sharper tools in the shedmjm540ii is one of the sharper tools in the shedmjm540ii is one of the sharper tools in the shedmjm540ii is one of the sharper tools in the shedmjm540ii is one of the sharper tools in the shedmjm540ii is one of the sharper tools in the shedmjm540ii is one of the sharper tools in the shedmjm540ii is one of the sharper tools in the shedmjm540ii is one of the sharper tools in the shedmjm540ii is one of the sharper tools in the shed
 
mjm540ii's Avatar
Name: Mike
Joined: Apr 2011, #54457
Location: Oxford, PA
Age: 26
Gender: Male
Posts: 731
mjm540ii's Tacoma Gallery
Nevermind, Got 'er done. The nuts were a little hard, but it wasn't a problem. WD40 worked better than silicone spray, but either will help. I ended up jacking it up, and put it on jackstands, just so I had the tires out of the way. However, I do not think it is necessary to jack the vehicle up, but I would recommend it.
  Reply With Quote
Old 04-14-2012, 03:50 PM   #3
Wannabe crawler
NC10TRDSPORT is one of the sharper tools in the shedNC10TRDSPORT is one of the sharper tools in the shedNC10TRDSPORT is one of the sharper tools in the shedNC10TRDSPORT is one of the sharper tools in the shedNC10TRDSPORT is one of the sharper tools in the shedNC10TRDSPORT is one of the sharper tools in the shedNC10TRDSPORT is one of the sharper tools in the shedNC10TRDSPORT is one of the sharper tools in the shedNC10TRDSPORT is one of the sharper tools in the shedNC10TRDSPORT is one of the sharper tools in the shedNC10TRDSPORT is one of the sharper tools in the shed
 
NC10TRDSPORT's Avatar
Name: Nick
Joined: Sep 2010, #43212
Location: PA
Age: 24
Gender: Male
Posts: 3,888
NC10TRDSPORT's Tacoma Gallery
Always jack the truck up when working on suspension parts
  Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Similar Threads
Thread Thread Starter Forum Replies Last Post
questions about u-bolt flip kit YotaKid62 1st Gen. Tacomas 3 04-10-2012 04:17 PM
All Pro Ubolt flip install question Voodoo Rufus Suspension 9 03-25-2012 07:46 PM
All pro ubolt flip. Brunes Suspension 11 01-21-2012 03:34 PM
all pro ubolt flip kit Wildlandtaco Suspension 23 11-09-2011 07:33 PM
Ubolt Flip Kit Worh It?? Snyperx 2nd Gen. Tacomas 2 04-02-2009 11:26 AM


Copyright © 2014 Tacoma Forum. Tacoma World is not owned by, or affiliated with Toyota Motor Corporation.