Mike "Wuzzy121". Rest in peace, brother

Go Back   Tacoma World Forums > Tacoma Garage > Suspension

Notices

lifting the rear and need help

Reply
 
Thread Tools Search this Thread
Old 12-11-2012, 10:08 PM   #1
yotatoy [OP] yotatoy is offline
Senior Member
yotatoy is on a distinguished road
Joined: May 2010, #37566
Location: il
Gender: Male
Posts: 118
yotatoy's Tacoma Gallery
lifting the rear and need help

i wanted to ask, if anyone knows,
if i lift the rear 1in to 1.5in
any other parts will i need other then the blocks or add a leaf

any help would help even were to buy the rear kit

thanks
  Reply With Quote
Old 12-13-2012, 07:40 PM   #2
yotatoy [OP] yotatoy is offline
Senior Member
yotatoy is on a distinguished road
Joined: May 2010, #37566
Location: il
Gender: Male
Posts: 118
yotatoy's Tacoma Gallery
its a 2010 tacoma

anyone
  Reply With Quote
Old 12-14-2012, 11:12 AM   #3
Senior Member
OverRated has much to be proud ofOverRated has much to be proud ofOverRated has much to be proud ofOverRated has much to be proud ofOverRated has much to be proud ofOverRated has much to be proud ofOverRated has much to be proud ofOverRated has much to be proud ofOverRated has much to be proud of
Name: David
Joined: Jan 2012, #71434
Location: San Jose, CA
Gender: Male
Posts: 309
OverRated's Tacoma Gallery
I recently did my rears and these are the parts I used.
- 2x Bilsteins 5100 (Not required but is recommended)
- 2x 1.5 AAL
- 2x Center Pin (3/8 bolt & nut from a hardware store) or buy them on Toytec. (For sure this will need to be replaced)

I would check out Toytec for your parts if you haven't yet.
http://www.toyteclifts.com/index.php...d=64&Itemid=72
  Reply With Quote
Old 12-15-2012, 01:48 PM   #4
4WD 4WD is offline
cRaZy oLdmAn
4WD is one of the sharper tools in the shed4WD is one of the sharper tools in the shed4WD is one of the sharper tools in the shed4WD is one of the sharper tools in the shed4WD is one of the sharper tools in the shed4WD is one of the sharper tools in the shed4WD is one of the sharper tools in the shed4WD is one of the sharper tools in the shed4WD is one of the sharper tools in the shed4WD is one of the sharper tools in the shed4WD is one of the sharper tools in the shed
 
4WD's Avatar
Name: Doug
Joined: Jul 2009, #19185
Location: Lakeside,CA
Age: 56
Gender: Male
Posts: 22,054
4WD's Tacoma Gallery
Quote:
Originally Posted by OverRated View Post
I recently did my rears and these are the parts I used.
- 2x Bilsteins 5100 (Not required but is recommended)
- 2x 1.5 AAL
- 2x Center Pin (3/8 bolt & nut from a hardware store) or buy them on Toytec. (For sure this will need to be replaced)

I would check out Toytec for your parts if you haven't yet.
http://www.toyteclifts.com/index.php...d=64&Itemid=72

This will work , get a couple grade 5 (or better) 3/8" shank bolts (preferrably threaded all the way) Knock the corners off (grind) & it'll drop into spring perch on axle nicely...

OP, avoid using blocks if you can...
  Reply With Quote
Old 12-15-2012, 05:07 PM   #5
Member
Bookin is on a distinguished road
 
Bookin's Avatar
Joined: Jul 2012, #82248
Gender: Male
Posts: 74
Bookin's Tacoma Gallery
You'll need longer u bolts too. Toytec has those as well.
  Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Similar Threads
Thread Thread Starter Forum Replies Last Post
lifting the rear trailinTaco 1st Gen. Tacomas 6 09-13-2011 03:55 PM
lifting the rear with TSB Larry Suspension 20 11-06-2010 09:06 AM
Lifting the rear after Fabtech installed cbcs1987 Suspension 5 11-02-2010 02:25 PM
Fine tuning the rear height after lifting the front? huff.jeremy 2nd Gen. Tacomas 4 03-17-2010 05:06 PM
Rear Sag under load without lifting volcom415 1st Gen. Tacomas 6 01-12-2010 07:26 PM


Copyright © 2014 Tacoma Forum. Tacoma World is not owned by, or affiliated with Toyota Motor Corporation.