Mike "Wuzzy121". Rest in peace, brother

Go Back   Tacoma World Forums > Tacoma Garage > Suspension

Notices

2013 Tacoma factory rear ride height?

Reply
 
Thread Tools Search this Thread
Old 06-25-2013, 05:30 PM   #1
Junior Member
RWSgunsmithing is on a distinguished road
 
RWSgunsmithing's Avatar
Joined: Oct 2012, #88154
Location: Iowa
Gender: Male
Posts: 10
RWSgunsmithing's Tacoma Gallery
2013 Tacoma factory rear ride height?

Well after adding a topper and filling a couple of tool box's my Tacoma's rear end looks like it's sagging a little. It looks really bad when I haul stuff. So I want to raise it back up to factory height. Problem is I didn't measure it before I added all the stuff to it.

So my question to all you is what is your factory Tacoma with the off road package rear ride height?
  Reply With Quote
Old 06-29-2013, 04:23 PM   #2
Junior Member
rfsdave is on a distinguished road
Army: 1166 Cbt Het Co. Kuwait/ Iraq
Name: Dave
Joined: Feb 2013, #98247
Location: Mass
Gender: Male
Posts: 15
rfsdave's Tacoma Gallery
Ground to fender with stock 265/70/16 tires: L/R 36.0 " and R/R 36 3/4" on my 2013 TRD Off Road.
From the center of the axle: L/R 21 1/2" R/R 22 1/4"
This is on a new 3500 mile truck. F'd up...Yes, so... I bolted a 1/2" plate to L/R spring pack and added 1/4" shim to the L/F strut mount to get the truck level side to side, front and rear. (the front shim brought up the rear 1/4" plus the 1/2" plate = 3/4")
Hope this helps
  Reply With Quote
Old 07-27-2013, 11:57 PM   #3
Member
Dfm155 is on a distinguished road
Joined: Apr 2013, #101873
Gender: Male
Posts: 39
Dfm155's Tacoma Gallery
2013 DCSB TRD Off Road 4x4
Ground to fender:
Driver side - 35 3/4"
Pass side - 36 1/4"

Hub to fender:
Driver - 21.5"
Pass - 21 7/8"
  Reply With Quote
Old 09-24-2013, 07:09 PM   #4
Junior Member
blaiwayw is on a distinguished road
Joined: Dec 2012, #92346
Location: Montana
Gender: Male
Posts: 4
blaiwayw's Tacoma Gallery
Good information. I also failed to make center hub to fender measurements on my 2013 TRD 4x4. Than I added an ARB deluxe front bumper and Warn M8000 winch. Big time front sag expected and it was so. Per ARB suggestion, I replaced the OEM front coils and Bilstein shocks with OME 886 springs and OME Nitrocharger N240 shocks. Front measurement fender to mid hub 23 inches. Rear 21.5 and I could see the sag. Installed ICON 3 leaf Add a Leaf in the rear. Now I'm 23.5 rear and 23.25 front. ICON claims a 1.5 inch lift and they were right on for me. Rides fine, couldn't be happier. No kangaroos in Montana, but plenty of deer. I don't see a difference in measurement drivers to passengers sides. Before the suspension changes I had a Taco lean to the drivers side of 1/2 inch.
  Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Similar Threads
Thread Thread Starter Forum Replies Last Post
Tacoma uneven at ride height Hawkvenom 2nd Gen. Tacomas 19 07-31-2012 01:26 AM
New shocks for stock ride height, smooth ride, and carry motorcycle kogary Suspension 4 02-04-2012 01:06 PM
Perplexed by my rear ride height decrease (Wheeler's AAL) BenWA Suspension 10 10-06-2011 10:45 AM
2nd Gen owners -- has your rear ride height settled since your truck was new?? BenWA Suspension 2 01-25-2011 01:44 AM
Tacoma stock ride height? gofas 1st Gen. Tacomas 8 12-18-2009 06:59 PM


Copyright © 2014 Tacoma Forum. Tacoma World is not owned by, or affiliated with Toyota Motor Corporation.