LSC15's 95 Tacoma 4x4

Go Back   Tacoma World Forums > Tacoma Garage > Technical Chat

Notices

New 05 Tacoma 4.0 clutch not grabbing problem. Need help!

Reply
 
Thread Tools Search this Thread Display Modes
Old 08-25-2013, 07:20 PM   #1
Member
xx99sublime89 is on a distinguished road
EMS: Medic Student
Name: steve
Joined: Nov 2011, #67645
Location: San Diego
Age: 33
Gender: Male
Posts: 20
xx99sublime89's Tacoma Gallery
New 05 Tacoma 4.0 clutch not grabbing problem. Need help!

So I just replaced my clutch on an 05 Tacoma v6 4.0 liter 6 speed manual transmission.

It was an aftermarket oem spec exedy clutch. I also installed the URD upgraded throw out bearing kit. Since installed and finished the replacement I bled the lines.

Problem:

My clutch will not engage until I am almost completely off the pedal. Being that its a brand new clutch I figured this would grab and start moving almost immediately...

CAN ANYONE PLEAAASE HELP ME!!!
  Reply With Quote
Old 08-26-2013, 10:59 AM   #2
Member
xx99sublime89 is on a distinguished road
EMS: Medic Student
Name: steve
Joined: Nov 2011, #67645
Location: San Diego
Age: 33
Gender: Male
Posts: 20
xx99sublime89's Tacoma Gallery
Ttt
  Reply With Quote
Old 08-26-2013, 10:01 PM   #3
Junior Member
mayan2k12 is on a distinguished road
Name: Carlos
Joined: Aug 2013, #111268
Location: San Pedro
Gender: Male
Posts: 3
mayan2k12's Tacoma Gallery
Looking to Replace my clutch on 07 4X4 6cy tacoma. Anyone out there know where i can get some instructions or videos?
  Reply With Quote
Old 08-27-2013, 01:41 PM   #4
Member
xx99sublime89 is on a distinguished road
EMS: Medic Student
Name: steve
Joined: Nov 2011, #67645
Location: San Diego
Age: 33
Gender: Male
Posts: 20
xx99sublime89's Tacoma Gallery
Quote:
Originally Posted by PSU Taco85 View Post
did you align the clutch correctly when you installed it? are you sure you bled the slave cylinder correctly? You may just be used to your old clutch, and FYI you can also adjust the pedal travel to where it engages the cylinder
I did align it correctly and i bled it correct to my knowledge and have always successfully done it. but i will look more into it.

Can you please send me in the right direction for adjusting the pedal travel? i seem to keep finding videos and post on it but it doesnt specifically show how its done. Any help would be fantastic.
  Reply With Quote
Old 08-28-2013, 08:34 PM   #5
Member
xx99sublime89 is on a distinguished road
EMS: Medic Student
Name: steve
Joined: Nov 2011, #67645
Location: San Diego
Age: 33
Gender: Male
Posts: 20
xx99sublime89's Tacoma Gallery
Quote:
Originally Posted by PSU Taco85 View Post
I don't have a link to the FSM but if you can find a link to it, it's explained pretty clear in there
FSM I'm assuming means factory service manual
  Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Similar Threads
Thread Thread Starter Forum Replies Last Post
Clutch kit for 05 Tacoma 6spd 4x4 for sale medicman4000 2nd Gen Tacoma Marketplace 1 09-13-2012 04:39 AM
second gear grabbing tig1 2nd Gen. Tacomas 21 07-16-2010 08:00 AM
Problem Starting my 05 Tacoma NightShades Technical Chat 13 10-11-2009 03:24 PM
05+ 2.7L tacoma clutch kit seryusly Buy / Sell / Trade 2 05-14-2009 10:55 AM
NEW Tacoma 05+ clutch kit (AISIN) jtaco Buy / Sell / Trade 7 12-06-2008 03:42 AM


Copyright © 2014 Tacoma Forum. Tacoma World is not owned by, or affiliated with Toyota Motor Corporation.