****OFFICIAL WET OKOLE GROUP BUY 2-18-16 -----3-6-16 ***** CLOSED

Yes, light gray: code 21. It's a little darker than in the pics.

 

My seat covers came in Friday, and I finally had a chance to try to install them yesterday. I say try because it did not go well. The backs were pretty good, although the slot in the back was way off so the seat doesn't latch unless you pull down on the cover for the back rest to allow the latch to clear. Sucks, but not a deal breaker. What is a deal breaker is that the fronts do not fit at all as they are way to big. I started with the passenger seat and removed the seat to make the installation easier. Both covers are way to big and bunch up. I'm thinking they made the wrong ones. I'm going to swing by their Costa Mesa location this weekend while I'm down in SoCal for a bike race and hopefully get it sorted out.

Pic. 1 - Fronts: Note the bunching on the lower cover and how the upper cover does not contour the seat.


Pic 2 - Latch is blocked by the rear seat cover

 

Mine did the same thing , then it jumped from being "cut" to "shipped".

 

What code did you use for that graphic?

 

Looks to me like the bottom seat fabric did not get pulled completely through, between the upper and lower seat. You have a 2 inch gap on the side bolster where the stock seat is exposed and should not be. Or... you have the wrong covers.

 

Couldn't find it on the site so I sent a picture from the interwebs.

 

They turned out great. Just curious, how tight are you guys tightening the buckle straps on the bottom covers? Mine were done pretty tight with the anticipation that the neoprene will stretch a bit. Just don't want to stress the stitching at the straps

 

got mine today and installed today.........love the color and fitment but had a few issues

1 - lumbar cut out was off enough that it bunches up

2- when latching the S hooks under the seat bottom one of them tore with barley any force

3- much like #2 I had 6 stiches pop right out while i was pulling the seat back cover down over the seat....I'd like to say I was using a ton of force but i wasn't.....kind of dissapointed in the fact I had two tears with out much force

over all they look and feel great, seat heaters are really nice, gonna wire them up nicely with some switches so they look factory. I'll grab some pics soon as I think my color combo might be one of the less purchased.......all charcoal, light gray piping

 

I cinched them really tight. Was afraid the buckle would break, but no problems
thankfully

 

I hope this is why mine are taking so long - maybe they fixed the issues after hearing from you and others....

 

Ordered 3/10- received, yesterday! A rocket fast 10 days! Outcome is exactly what I was looking for! Wet Okole was awesome, by allowing "custom" manufacturing with the charcoal bolsters, not black or solid.

 

I'll order a set if they offer the same deal.

 

When I ordered, I wanted a brown to match my quicksand exterior for my 2016. For future reference, the tan is not that great of a match. It looks more like a super light sand color (almost white/light gray) rather than a traditional tan.

 

How many 2016 owners have had a problem with the seat latch being covered?

 

Look great! Went from cut for a week to deliverd next day lol
Idk how i feel about the lumbar support
And i dislike the console cover

 

Spoke with wet okole and they fixed my problem they confirmed that I will get the care kit once I pick up my order at the Costa Mesa location anyone else with the same problem I had, I advise y'all to call them up good service

 

Installed them first with the seats still in , but them removed the seats to reinstalled with a tighter fit

 

Im in if its not too late!

 

Calling them today! So far I have only five people including me who some so well see.

1. @ThunderTacoma
2. @caNtstOp
3. @MQQSE
4. @bdcarp0
5. @Makule Taco

 

I'm in and ready if we are ordering more seat covers!
I've been debating between WO and the Clazzio attached.