What have you done to your Tacoma today? 1st Gen Edition

Got a few parts and system to install

 

Got my CB mounted in yesterday!

 

Yea I run the bamf kit with the shocks angled /\ and feels fine on the road... the more vertical and outboard you move the shocks the more "stable" it'll feel

 

What model is this one?

 

It will depend on how far you angle/lean the shocks back. The upper portion of the shocks will be right where the tire wants to be.

A great excuse for a swingout tire carrier bumper.

 

This spring......

 

One thing to consider when doing a shock relocate like the BAMF setup is, the further you lean the shock from veritcal, the less efficient it becomes. At least that has been my experience.





I found I needed to re-valve my Foxes to add both compression and rebound to get them where I like them. If you are buying new from DSM, I would tell them of your relocation plans so they can adjust the valving accordingly.

 

The Cobra 19 Ultra III. It wouldn't fit without cutting some of the back of the dash out, but with some industrial strength velcro it fits in quite nice.

 

Another thing is that because of them being on an angle the shocks progressively get less effective throughout the travel because the angle theyre at will increase. That cant really be fixed with regular valving.


unless you want the most articulation i prefer the shocks being as straight up as possible and as close to the wheel as possible. That gives the most stable and consistent ride. The downsides are that your limited to the length of shock used inside the frame (without going through the bed) and youl need less backspacing to put them outside the frame.

 

I'm seeing a lot of different kits I prefer to go with everything OEM, is this the one you got?

There's this one as well

Genuine Toyota Timing Belt Kit with OEM Aisin Water Pump for 3.4 V6 5VZFE Engines

https://www.amazon.com/Genuine-Toyota-Timing-Aisin-Engines/dp/B00I0Z14AW

It says ones Aisin and one's koyo. About a $20 difference.

Also it comes with a thermostat which I don't really want since I want to put a TRD tstat in instead but looks like I can't find a kit that excludes it.

 

The kit I linked is all oem. They use different manufactures. Check the description and it gives you the manufacturer and part numbers for each.

 

Ah ok thanks. Just being sure cause there were similar kits that say "generic parts" of course for a lower price.

 

So I was installing my new suspension and discovered that the spindle up top is loose. Or ball joint is loose. But the actual ball joint isn't really loose. Pretty sure it's the spindle. Because we checked the torque on uniball and was still tight at 170ft lbs. Couldn't remember what it was supposed to be. Driver side doesn't do this. The uniball seems tight in the control arm as well. Just this.
(yes I know, she's filthy)
https://youtu.be/vDjcp1IzQy0

 

What is the part # for OEM lbj assemblies? 03 3.4.

2000 miles till my trucks 200k mile birthday so getting a list of part #s.

 

And are there any Toyota sites or TRD sites having Black Friday discounts today that anyone knows of?

 

Yup, that don't look good. Looks like the spidle opening is too large. My Camburg mount had to be pressed in. Yours looks like it would fall apart.

 

@45acp and I had a date today. Usually that involves looking at my truck, coming up with something to do, breaking something, then resolving it.

So we swapped out the CV on my passenger side with an OEM one that's been sitting in my shed since Jon dropped it off years ago. The upper boat ripped off the collar from dry rot.

Then we ran into a problem.... how the fawk did you remove/replace the CV with the sway bar knuckle/link in place? We decided the only way was to remove it.

Then we broke something.

The bolt inside the bushing was so rotted from rust that it just snapped in half.



So no sway bar for now. After test driving it, I decided I want to put it back on.

Also... we found a lot of oil on the splines that go through the hub. Anyone have ideas? Jon thinks it's just the residue from grease breaking down.





And for prosperity's sake... the blown CV boot



More dry rot:

 

$201 43340-39585 Toyota Genuine Parts - Joint Assy, Lwr Ball (43340-39585)

43340-39585,

$214 43330-39815 Toyota Genuine Parts - Joint Assy, Lwr Ball (43330-39815)

43330-39815
And the bolts are:
90080-10066

 

how was the link in the way? ohhhhh you musta never removed the strut?

 

I had to remove the link when I pulled mine. I did not remove my strut.