Great White Taco build

Im almost off work! 1.5 more hours! Then 2 days off

 

So instead of cluttering up @HolyHandGrenade build thread, I thought I would tag you here @stairgod .

Need some help planning.

Compressor ->

$21 Viair 92804 18" Stainless Steel Braided Leader Hose without Check Valve

stainless leader hose ->

$9 Anderson Metals 06102 Brass Pipe Fitting, Barstock Cross, 1/4" x 1/4" x 1/4" x 1/4" NPT Female Pipe

4x female port for ARB inflator kit quick connect/pressure switch/

$9 Legris 3109 60 14 Nylon & Nickel-Plated Brass Push-to-Connect Fitting, 90 Degree Elbow, 3/8" Tube OD x 1/4" NPT Male

male NPT elbow to 3/8" tube/leader hose ->

Legris 3175 60 14 Nickel-Plated Brass Push-to-Connect Fitting, Inline Connector, 3/8" Tube OD x 1/4" NPT Male (Pack of 4)

male NPT inline to 3/8" tube/

$9 Milton Industries (S-766) 3/8" FNPT Female V-Style High-Flow Coupler

3/8" quick connect



Am I right? good plan?

 

Sounds fine. How many quick connects are you adding? If only two, use a regular tee instead of a 4 port connector.

 

Or just use the 4 port and plug one hole for future use with a front locker.

 

one, in addition to the one that comes with the tire inflation kit. Which is why I had a 4 port. In this video, the guy uses all 3, on the included Tee. Around 4:05
https://www.youtube.com/watch?v=S9yOAamRmJg

 

Pressure switch? Or regulator? The compressor has its own pressure switch.

 

Exactly. The twin has its own pressure switch. So you can eliminate the 4 port entirely.

 

the pressure switch that comes with the compressor.

So the one referenced in the video, is not included in the twin compressor? And therefore, I dont need a 4 port connector? A 3 port would do just fine?

 

I ordered this manifold. It has two 1/8" ports for my selomoids and 4 1/4" ports for whatever. I know I could've used T's and such. This was just easier to buy this. Also,easier to mount and run my regulator out the side.

It's cheaper and has more ports than the ARB manifold.
http://www.ebay.com/itm/321966081822?_trksid=p2057872.m2749.l2649&ssPageName=STRK:MEBIDX:IT

 

Not bad. The ARB solenoids are 1/8" NPT???

 

I believe that's what the guy at ARB said when I called the other day. They're not 1/4" that's for sure. Whatever size they are, that manifold is advertised to be correct for them.

 

Thanks for the link! I will definitely be looking into this, when I get closer to my assembly

 

If you're planning to add lockers one day, I'd just buy this now. Plug the holes for now. Then you're ready to go when the time comes

 

I cant decide if I want a front locker. Stickers said it wasnt necessary..

 

Depends on what trails you prefer to NOT be able to do. Front locker can be very useful.

 

have we done Tatas?

 

You did not yet I think.

 

I did Tatas with Steve, Lloyd and Garrett IIRC. No need for a front locker there. Tim needed his to do Yellow Jacket

 

That, and finally getting the right line. I'm nervous about breaking an axle every time I turn it on though...