AZ BS Thread 4²0

If it's for only a welder or comp, then 10/2 or 10/3 is too small. A compressor will pull 30A easy. A welder depends on the size but it's usually a 50A which requires 8/2. No need for a neutral. That would be for a modern appliance like a washer or stove that needs it for the computer.

It's easier now to run larger wire and size down the breaker than once the house is built.

 

It's not bad in traffic when you're getting paid for sitting in it. 3 hours till I call it a weekend

 

Some are more anal about it than others. One of my buddy's had to cite no mudflaps when he was on FTO (field training) because he was ordered to... all depends who's on the road...or if you kick a rock up to chip the windshield. That doesn't go over too well


I have a quick release on my mudflaps for the ferd.

 

We installed a 50amp breaker in my neighbors house for his welder. Went 6/2 for the wire size.

 

What is considered lifted? Bigger tires, suspension, frame height, all of the above? What if I have bigger tires than OEM but my frame technically sits at the same height?

 

A.R.S. 28-958.01. Rear fender splash guards

A. A person shall not operate a truck, trailer, semitrailer or bus on a highway unless the vehicle is equipped with rear fender splash guards that comply with the specifications provided in this section.

B. The splash guards:

1. Shall be attached in a manner that prevents the splashing of mud or water on the windshield of other motor vehicles.

2. Shall extend to a length of not more than eight inches from the ground.

3. Shall be wide enough to cover the full tread or treads of the tires being protected.

4. Shall be installed close enough to the tread surface of the tire or wheel to control the side throw of the bulk of the thrown road surface material.

5. May be constructed of a flexible rubberized material.

6. Shall be attached in a manner that, regardless of movement either in the splash guards or the vehicle, the splash guards retain their general parallel relationship to the tread surface of the tire or wheel under all ordinary operating conditions.

C. This section does not apply to:

1. A vehicle commonly known as a pickup truck with a manufacturer's gross vehicle weight rating of ten thousand pounds or less, except that this section applies if the pickup truck has been modified from the original bumper height design to raise the center of gravity of the pickup truck.

2. A truck tractor or converter dolly when used in combination with another vehicle.

3. A single, tandem or triple axle trailer with fenders that are wide enough to cover the full tread or treads of the tires being protected and that extend to a length of not more than fourteen inches from the ground.

 

If your souless ginger like me have your dermatologist write you an RX for dark window tint!!! I'm outside allot so every little bit helps lol

 

You really have a RX for window tint?

 

I wish I could carry at work.

 

It's pretty common here, CA and Fl for that!

 

Interesting. I never knew that but I'm going to have my wife go get an RX for it. She loves her limo tint all the way around her truck.

 

Usually it's for skin cancer patients, or people prone to skin issues with sensitivity to light

 

Yeah dude ! I didn't know about it until my Doc recommend it. Im a dirty ginger and my job requires me to be outside allot so I get looked at once a year for the hell of it. I haven't upgraded tint since I've gotten the taco last year but eventually will.

 

My office is VERY pro 2nd.. On any given day, there's at least 10 firearms in here. We even have a corporate membership at Scottsdale gun club

 

Where is the service in relation to the garage out of curiousity?

 

Cool, that's what we're doing

 

6 feet

 

That's nice. If someone robbed our parking lot at work they would have a safe full of hand guns....

 

We can't bring our guns into the office.

A lot of people still do.

 

Coilovers are ready for pickup! Woot woot!