Finally sold-Swingout Tire Bumper and Bed Rack-PRICE REDUCED AGAIN AGAIN-675

Price reduced 675 for swingout. My swingout bumper. BED RACK IS SOLD

Swingout bolts to factory rear bumper location and is built to fit a 37" tire. Currently has a 35. Uses four studs and the Ruffstuff Spindle. Feel free to ask more questions. Uses a T handle to secure in place and has an air craft pin to hold open and close. Includes hitch receiver. Bottom is scratched from being dragged but does not affect anything. Asking $675 plus shipping but would prefer local pickup. Could meet part of the way.

Bed rack with 2 Rotopax mounts, Cb antenna mount, traction mat mount, and highlift mount. Was made to hold a RTT with enough room to hang the annex and stand up in it. I am 5'10"/5'11" and could normally walk under it with a 2.5"-3" lift. Uses 4 bolts to mount. Also has tie down points and is powder coated. Sold

Bedside Guards. Not sure if their is any interest in the bed side guards. Mounts to the hitch receiver where it is bolted on and then welded to the frame. Will take $75 plus shipping. Also scratched and one side was pushed in a little but has saved my bedsides countless times. Also have mudflaps for them.

Sure im missing stuff. Could do a package deal. Let me know if you have any questions.

DSC_0068 by Harrison M, on Flickr


DSC_0065 by Harrison M, on Flickr

20160903_174519 by Harrison M, on Flickr

20160903_183809 by Harrison M, on Flickr

20160903_174448 by Harrison M, on Flickr

 

@m3bassman @Speedytech7 swing outs and bed rack

 

Good looking out, I like both but shipping would destroy me and I'm not going to NV anytime soon. Good luck with the sale @malburg114

 

You bought a really short garage, even with my goofy rear lift and a raised canopy I fit with 6" to spare in mine and inside the garage I can even have my antennas up.

 

Heading to the Rubicon (Lake Tahoe) in September if that makes a difference? Hoping I dont have it by then but.... Could always ship with fastnel or throw it on a grey hound.

 

This has been stated in several other posts. 2nd try was not the charm!

 

Ouch, I hear there are pills for that

If nothing else, our stupidity is keeping his thread in the public's eye haha

 

Nice set up buddy, I really would like a swingout bumper It's annoying packing up the bed with a tire in there....

 

Why don't you run it in the stock location again?

 

Too big would need to mod it, and it hangs down too low. Also IMO it looks ugly lol

 

I'm asking cause I didn't think I could fit a 33" (255/85r16) but it fits just fine. I did cut off the ends of the spare tire carrier but that was no big deal.
And hey, outa sight, outa mind right...

 

Ya fo sho lol, But with my high clearance rear bumper it will drag on the tire at certain angles and just be too visible with a 305/70/16 i think

edit- shit i was actually considering it but i tossed out the mounting arms that were down there lol all i have is the hanger

 

Make an offer if you really want it. Looking to sell soon so I can buy more lol

 

I have never had those bars FWIW and my tire stays in place

 

@cynicalrider @sente3 @04yota

 

Oh BS.

The antennas unscrew very easily.

 

So your selling your rear bumper and the swingout tire carrier right. I live in Phoenix I can probably meet you up near kingman az if the price is right.

 

That is correct. The swingout is part of the rear bumper. Bolts to factory location.
Shoot me a pm with an offer.

 

Also interested in trades for 17 in wheels, 5.29 8 in 3rd members, trail gear rock assualt tacoma width housing or the likes (highly doubt) and chromoly axle shafts lol.

 

Sick bumper. I'm sure it will sell quick