Wyoming B.S. Thread

Lol I was going to say 78's, but having never met you I was unsure of the era

 

@Speedytech7

Whitney contacted me. Its the right ECU.

Gonna just see if they can ship it.

 

I bet they will, they had a dude there just doing phone orders and they don't let you pull parts yourself.

 

Mesozoic

 

Got my Kings back from Tim. Can't wait to get them back on. I was surprised at how anxious I felt while they were gone.

I have a question about 1st gen IFS wheel travel. Without the shock in there, it looks to be about ~9" from full droop (no wheel mounted) to full stuff, all the way to the slightest compression of the bumpstops. Is this typical? How does this compare to a 2nd gen?

It does not seem like my mid-travel Kings can take full advantage of all 9"s.

Full disclosure, this is with Camburg UCA/1" uniball and OEM LCAs and ball joints. Also no anti-swaybar.

 

I'd like to know as well, I know my icons take advantage of every last bit of down travel but the up travel is unknown to me.

 

How is it on the highway with no sway bar? Curious about it for off roading but have read it can be sketchy at highway speeds

 

I like it. But I do have 700# coils. Honestly, have never missed it.

Its worth trying out on the highway to see if you can get used to it. Off road there is nothing to dislike about not having one.

Instead of totally removing it, you can disconnect each end and rotate the bar so the ends point up. Zip tie them in that position and go do some slolom racing at 70 mph.

 

I'll give it a shot now that it's becoming less of a DD

 

To paraphrase something I once saw Ben write...

An anti-swaybar is a lot like a condom, it feels safer with one on, but feels so good without one.

 

Even with my last setup (Eibach poop coils and Blown billies) having no sway bar was a night and day difference, not as rough over bumps and the body roll was 100% manageable. Even evasive maneuvers were okay, just try them beforehand to make sure it works for you.

 

Let's not forget that condoms have other purposes than modification of feel, the bar actually prevents body roll just like a condom prevents you from ending up with an 18 year burden. But I suppose the comparison is accurate in that neither are 100% effective

 

Yeah...long as it isn't 20 bucks haha Hopefully hear back tomorrow.

Was fast they pulled it today.

Well, did you lever the arm down? i know the LCA bushings hold up the assembly a bit by themselves. So could be more.

But 9'' sounds right. Though i think you're right that the shock won't allow it full travel still. Think you'd be lucky to see 9'' of wheel travel.

Why Long travel is a thing. 14'' of travel. Amazing what a difference it can make to have just a few more inches of travel too. So much smoother.

2nd gens are similar travel.


also...tim? who rebuilt them??

Igor hasn't had a sway bar since the kings went on. Very much worth taking it off.

 

No worries, I'm not going anywhere so if shipping is nutso I can grab it and hold onto it until Oregon

Also I think he means Tim F. @TMFF

 

haha that is fair. Or i'll have you ship it. Will want to test it out ASAP.

Then the SnapShot goes away in June finally and i can drive Frank the way he was meant to be..



ooohhhh gotcha! Nice. That dude knows his stuff!

 

I did. It was at the bottom of the travel, I could not lever the arms down any further.

It was interesting that the 2 sides are not identical. Surprise, surprise! The passenger side movement is about 1/2" higher than the driver side. There is also a slight difference in the amount of travel from side to side. The driver side is ~1/8" more.

Are there any established numbers for extended travel King's OEM COs? I guess I'm asking how much of the 9"s are we able to use?

Yeah, Tim from 303 Shock Services out of Henderson CO.

 

Rubber bushings in the LCA? What's the limiting factor in your downtravel?

I have right around 9", any more and the CV binds.