2012-2015 4.0L MGM OR Stock Parts: Bumpers, Steps, Skids, Misc Engine Parts

Time to clean out my garage! Details for items will be listed below the item pictures. All items were removed from my V6 2014 TRD OR in MGM.

I am located in Mineola, TX (north of Tyler in East Texas), and can arrange to meet in DFW, Tyler, or the Houston area if possible. I will not ship anything at this time.

Thanks for looking!


Front bumper cover in MGM, removed at 50K miles. As you can tell by the pics, this bumper has seen a few rock chips and scuffs in its day, but it's solid. Initially, this bumper was to come with a free bonus wasp nest, but I figure that deal would have been too good, so I removed it. $250


Front Bumper Aluminum Crash Bar and Bumper Supports - removed when I installed my plate bumper at 50K miles. No longer have hardware, but it shouldn't be hard to source. $80 ... or buy it with the bumper cover for $300 even


Predator Steps - removed and reinstalled a few times, but only saw about 20K miles of use. They still have some wear marks on the underside and mounting points. Mounting hardware included. $200


Front Skid Plate - removed when I installed my plate bumper at 50K. It's shiny in this pic because I had just washed it off, but it's got a matte stock finish, could use a coat of paint to touch it up though. You'll notice I cut out the rear corners to round it out to clearance my lower control arm skids. $30


Mid Skid - removed when I installed my plate skids at 55K. It's a bit shiny in this pic because I had just washed it off, but it's got a matte stock finish and some rusting scrape marks. I'll wire brush it and put a fresh coat of paint on it if interested. $30


Stock Full Size Spare on 16" Steelie... the pics do the talking, put a few miles on this one while I waited to upgrade to 33s. $50


Front Grille Assembly... removed when I added my homer taco grille about 40K miles. It's derped in plastidip and is chipped away in several spots. Needs to be refinished, or remove the derp for a chrome grille surround if that's your thing. Also has raptor style LEDs installed ready to tap into your parking lights. I grew out of them... the far passenger side LED is a bit dimmer than the others, so if you want to run them I'll link you to a new LED. This is priced cheap because it needs work to fix up. $20


Rear Bumper... removed when I added my high clearance bumper at 50K miles. It's derped in plastidip because I wasn't a fan of the chrome. It may need some slight touch ups or you can remove the derp to revert back to chrome. Does not include license plate lights... does include stock hitch assembly. Will get a hand and clean it up if a buyer is interested. $300... will not remove hitch from bumper, you must purchase as one unit.
Stock TRD OR leaf spring packs... removed at 23K miles when I swapped them with Dakars. $50


Want to paint your engine cover, but affraid you'll eff up yours and be stuck with an ugly mess under the hood? Buy this engine cover as a backup! $20


Brackets - on the left is the stock power steering reservoir mounting bracket $5
The long brackets are for the stock front skid plate mounts $10 or included with stock front skid purchase
The small parts on the right are end caps to the accessory rail system. I don't know why tf I have those in there. If you want them you can have them for free.

 

I need two rail end caps, but not badly enough to arrange a meet

 

I'll be in Fort Worth Wednesday for work... I'll spend the evening hours catching up with some work buddies at one of the bars near the W. 7th area. If you work in Fort Worth we could meet up then, I'll throw them in my console just in case.

 

That might work. Thanks.

 

No problem. Just shoot me a PM to let me know so I'm sure to get an email notification in time. My Fort Worth office is at University and W. 7th.

The rail systems are the same between 2nd and 3rd gens, or do you need them for a 2nd gen? Just want to be sure we don't waste any time or anything like that.

 

Rails are same.

3rd gen doesn't come with the rail at the head of the bed, so I bought one and put it on, but it didn't come with end caps.

 

10-4... you can have all four if you'd like to have a couple of spares.

 

Any interest in trading the predators for shark rails?

 

I've got sliders so I have no need for any kind of steps, unfortunately.