What have you done to your Tacoma today? 1st Gen Edition

I bought the rotors, calipers and pads from O'reilly's; my brake lines came from Wheelers off-road('02 Tacoma lines). I told(O'reilly's) them to give me parts for a 2004 Toyota Tundra 4.7liter, SR5, 4wd, dbl. They have a lifetime warranty.
I looked at the kit on Amazon, it seemed ok, but when I googled company names it all got real blurry. I backed out and emptied my amazon cart. That was just how it was for me, I think the cooling vanes were 1/2 of the OEM to. Just give them a good thorough look over before buying, the darn item & seller changed up several times. NAPA, also has a good set you can look at. Goodluck. Either way you go, it will be well worth it.

 

what did the o'reilly's stuff run you? I was about to pull the trigger on Amazon..

 

Rotors #96931RGS $57.99ea X 2= $115.98
Caliper #19-2712 $77.99
Caliper #19-2713 $77.99
Ceramic pads #SC976 $39.99

The Amazon parts might be ok, just check them out from every angle.

 

I posted this on page 6407...here's how the O'reilly rotors & calipers look installed

 

Thanks, sorry hadn't looked through the back pages before replying..

 

No problem. I'll help anytime.

-Malcolm

 

I meant the bearings in your PS pump, not wheel bearings lol

 

Oh..lol. My bad

 

Bad ass man!!

 

Thanks, have lots of plans for it

 

You dont always have a direct line to pull.

 

thus snatch blocks..

like so:

Memorable Oregon-16.jpg by Monte Nickles Photos, on Flickr
Memorable Oregon-17.jpg by Monte Nickles Photos, on Flickr

 

Changed out dual electric fan and went back to crank fan on 96 4x4 LT taco. E-fan couldn't take the heat...fine for city driving and light offroad, but sand wash and hill climbs would send the temps over the hill.
Going back to stock was a good decision. Temps hold solid, actually run cooler on the trail than freeway, says the Ultraguage.

 

Picked up a set of BMW leather, power, heated seats at the salvage yard today. Came with the cut off of the wiring harness. Spent the evening on various BMW forums, searching out wiring and connector diagrams. Have most all of the wires labeled. Taped up the side air bag ones, so no accidental deployments!! Tomorrow I will begin testing the various functions. If all goes well, then it will be on to grafting my rail feet onto the BMW rails. They are almost a perfect match width wise, so not a terribly involved fabrication. Just have to get them properly spaced forward and back, to allow my 4' 9" wife to reach the pedals and give me ample leg room too. Pics to follow!

 

Its a Uniden Pro 520xl. I took the picture at night right after i finished installing it.

 

I need to get this

I dremeled out the plastic in the back of the ashtray and removed the ashtray bracket to get it that far. Then i made a custom cable Using a right angle crimp on pl259 connector such as this image without having the need to heat up the air duct behind the ash tray. You can probably find a premade cable somewhere on ebay. As for mounting it in the ashtray i used a few zip ties and 3M double sided sticky tape, Its not ideal but it survived the summer heat.

 

Ordered these warehouse deals the lbj said good condition and the otre said like new. Even if they're kinda jacked they'll probably make okay oem spares.

 

When you get the LBJ make double sure they are OEM toyota and not just Sanki/555/Moog. You can tell if they are OEM by seeing if the mounting holes are machined out.

 

@Speedytech7 did you swap out your pilot bearing with the new clutch? I've been scoping out ways to do it. Wondering what is the easiest for these trucks!

 

Yah I swapped it. I'm a cheap bastard so I packed the space behind the bearing with grease and used the pilot install tool as a piston and hammered the grease in and the pilot gradually comes out. Just gotta keep repacking and hammering.

https://youtu.be/VHnTZLT2ihw

This guy does it right but I didn't bother with a loose fitting extension, went straight for the clutch alignment tool because it has the exact pilot bearing inner diameter.