AZ Classifieds

Which one do you need?

 

Details details

 

I think it would be the smaller one, but I would need the base too... it's a long story.

I added fog lights to my Taco and the switch I got was a 2015 "light green" style that clashes with my 2016+ blue style, so I figured I would get an LED to match... well the LED sucks and lights it up really dimly so shocker, I wanna go back to incandescent but the incandescent bulb I had is "somewhere" in my parts pile 2500 miles away in Pennsylvania.

I figure I'd rather have it well lit and just roll with the orange because at least it won't look like I tried to match and screwed up.

I've got a gift card to a Toyota parts department so I could just grab one, but they are like 6 bucks a pop which is silly.

 

I only have the bulbs... Sorry man. And where did you get the LED from? Because I went to LEDS and all my dash lights are way bright

 

No biggie I'll just order it then. Thanks for looking though!

LEDs I just got a generic 5 pack off Amazon. Kinda shitty little things to be quite honest.

 

Haha well then there's your problem! Get some actual nice quality LEDs and they'll be plenty bright. Superbrightleds.com
All the dash lights on my 04 Tacoma I got from there and I also did the gauges on my 93 Mustang. They look so nice and are really bright.

 

Brightness isn't the issue, it's the fact that the bulb goes in sideways into the switch housing. With a little surface mount LED mounted flat, the throw of the beam hardly reaches the button.



It would work fine on something that points directly at the part it is supposed to light up.

 

BUMP!

 

For the snowboard??? Let me try to find the post

 

@DukesTaco

 

Cabelas camp kitchen deluxe .
75.00
Good condition . Table does have a couple small cracks where I pushed too hard to clamp it to the bar.
Just put some duck tape on there.
2 lantern holders, 2 cordura storage departments that attach under the tables.
Sink that snaps in ( never used)
Sets up in minutes. Carry bag included.

 

https://phoenix.craigslist.org/nph/pts/d/tacoma-4runner/6458153403.html

entire 4x4 drivetrain, with supercharger for 1800

 

Visor 450P. This is the 100% duty cycle version and works extremely well. Bag, hose, inflation gauge. $150

 

@Milota95 get your old truck running!

 

Ruger MKII 10” bull barrel w/ scope. Slight play between barrel and receiver but does not effect function or accuracy. With this scope I can hit steel offhand at 100 yards.
2 OEM mags, 2 aftermarket mags that don’t feed well, scope, and OEM rear sight. Has extended mag release installed. Minor scuffs on one side of barrel.
$600

 

fooock

 

[/QUOTE]
The Texas bevel is sweet. Is that your best price?

 

Might get rid of my Scorpion EVO S1, not sure what a fair price would be on it. Good condition, low round count (less than 200).

 

If you were going from matte to matched, you'd find someone in the 3rd gen "fender swapping and trading" thread in a heartbeat. Matched to matte is like asking to trade an unscooped hood for a scooped hood... more unlikely. (speaking of which wanna trade hoods? )

Don't wet sand, just use matte black plasti-dip. 2 or 3 cans should be plenty to do all your flares. If you follow a good guide it looks exactly the same and you can undo it if you don't like it. Easy enough to do on the car, but will look better if you carefully remove them to spray.

Also the ninja secret to not snapping your front flare's tabs off is to undo the fender well liner and reach behind there to pop them out:

See that lower flat head screw? Turn it 90 degrees and you can push the mud liner aside. (This is also how you're supposed to change your fog bulbs FYI) and you will be able to get at those buggers. Squeeze the 3 clips from behind there and they will pop out easy peasy without the potential to snap them. This is what they look like:

Ignore the pliers and don't do that. It's from my mod guide to fitting them onto SR trims without the holes.

Good luck, hope this helped!

 

Thanks for the info!