What Have You Done To Your 3rd Gen Today?

Just press and work them in to the headliner. Some stick better than others

 

Had the day off today.....thusly I did a couple little lightweight interior mods after getting home from lunch (my breakfast) with my son.


He's been after me to go to one of his favorite spots....some type of fusion burrito restaurant. He volunteered to drive us in his car....I veto'd that and we took the Taco.






Did a couple small interior enhancements later on in the afternoon.


Much thanks again from the folks from Hondo Garage & Tufskinz. These will be some useful additions.












Before:









After:










Before:








During:









After:









Since Hondo Garage didn't have a 1911 pattern.....I went with their AR15 bolt carrier group engraving.












Then for the after-after pic......
















Soon it'll be time to use the tailgate on my Taco as I cook up some dinner that will satisfy the hunger that has built since skipping breakfast and going to lunch to what turned out to be some hipster bs excuse for a burrito restaurant only to take a few bites and tap out. I ordered one draft when we got there....and was served some type of cider junk that was horrid. The music they were blasting should have been warning enough that I was out of my environment, lol.


Live, learn and prosper.....or whatever Spok said.


I'll be chilling and grilling in short order.

 

Bridgestone RB1

 

I need to source 2 rear parking sensors, and 156 each is the best I can find online! Anyone have any experience with a good online source for salvage parts?

 

They're not 35x12.50s.

Wheel well liners are trimmed and a very aggressive CMC was done. No rubbing. If they 'poked' more I'd probably have to trim the fenders.

 

Gorgeous !!!!!!!!!!!!!!!!!!

 

Hahahahaha, not sure why but I got this vision of you trying to squeeze into a pair of skinny jeans before you went!!!!!!

WAIT! Hondo sells knives?! I like knives!

 

Wow... Beautiful pup! Bet that cutie is a chick magnet!

 

Only thing my fat arse knows about skinny jeans is the fact that my wife called me earlier today......and brought me up to speed on some time she's spending this week in coastal NC with her family.....and went shopping with our nieces....bought a pair of skinny jeans for herself........they are distressed and have cuts all in them. My near 50 year old self instantly went to Whitesnake video in my mind....Tawny Kitaen on the hood of the car in "Still of the Night" video. This is way out of character for her and completely suitable as far as I'm concerned.


Said she was ready for our next "date night".


I'd better get back in the gym tomorrow.

Old guys gotta represent.

 

Noice!!!!

 

K&N Model 77 (Chrome) CAI. MBRP 3" Cat-back, single side exit with 4" chrome tip.

 

I'd like to hear that biatch!

Is this a Ebay deal (the K&N)?

 

I'll get around to a video/audio of it, at some point.

eBay? No, I ordered direct from K&N.

 

Installation was easy but holy cow you took the much harder route! I just took off 2 screws and a plastic push thingy out (for each wheel well) and then pulled back the trim of the wheel well enough so that I could put my arm and the fog light through. I did not removing of any trim (grill/fog bezels/air deflectors/etc). I was done with both sides in about 25 minutes (not including the aiming process which I had to do later when it was darker).

Although, I must admit that your way was probably MUCH cleaner than mine. LOL

 

You can reach them from the engine bay so you don't need to pull the liners

 

didnt make much difference in sound. plus my phone saved it as a mp4 and it wont let me upload mp4 to the site.
and I had nobody to push gas while i recorded

 

True, you can definitely reach the fogs from inside the engine bay just by reaching down under the headlights. The reason why I went through the wheel well is because it would have been a awkward angle (and a big stretch) to get under the new fogs to adjust the aim once they are installed.

 

This happened today

Before



After

 

I like your license plate cover quotes, at least the idea, can’t read the second one though. Oh and looks good!

 

Not sure how but got these in 1 day from TRS?