3rd Gen Taillight Chrome Delete

post some pictures with this and the smoke together, i might order them too..

 

A bunch of these have shipped anyone get around to Installing yet? Lmk if questions before Installing thanks guys

 

Weather permitting, once I get mine, I'll install em and take pics asap! I got my galaxymoto trim covers today (linked below), so I can install those at the same time too. Unfortunately expecting lots of rain tomorrow.. and potentially some more on thursday. So hopefully mother nature will allow me a few minutes to slap both of these on, and possibly my meso "b" grade ultimate led side mirror turn lights at the same time!

I assume they just apply right on? Or should I go for the spray method? I normally just try my luck and go for dry applications, because eh.. why not, and I'm stupid.

 

To install the taillight overlays


1. Clean the appropriate area of the taillight with some rubbing alcohol. This will remove any dirt or oils from the area prior to installation.

2. Spray or splash a bit of soapy water (or vinyl application fluid) on the appropriate area of the taillight.

3. Remove sticker from the paper backing. It is recommended that you use some masking tape to lift an edge of the vinyl decal in order to avoid damaging or stretching the vinyl, but if you are careful, it can be done without.

a) If using a spray bottle to apply soapy water, spray a modest amount to the adhesive side of the vinyl, this will allow you to have more freedom to maneuver it into the correct spot before it begins to stick.

4. Slide the sticker into place on the outside (lateral) portion of the taillight first. Because of the slightly raised edges on the taillight, this part should slide right into place with a little patience. Once in the correct location and the alignment is correct, begin to push down and squeegee the soapy water out from under the vinyl with your thumb or finger. This will allow the vinyl to stick in place. While sliding the water solution out from under the vinyl, continue to have one or more fingers holding the vinyl in place so that it does not slip and slide around.

a) If you find it helpful, use a cloth towel (preferably microfiber) to blot out and absorb the excess water and moisture around the decal.

b) If you notice bubbles forming under the vinyl, gently use your thumb to squeegee them towards an edge and out from underneath.

5. Next, wrap the two tails around to the interior (medial) portion of the taillight towards the tailgate. Be careful and make sure they are straight and as parallel to the ground as possible. Once in place, use your thumb or finger to squeegee out the soapy water from underneath.

6. This will leave you with a cone-shaped tunnel/pinch in the center portion of decal, in between where tails meet the solid, square portion of the decal. Use a heat gun on low or a hair dryer to begin to shrink this raised tunnel portion down so that it will stick flush to the taillight without folding over on itself. Use your thumb/finger to press the vinyl down carefully: work from the narrower (smaller) outside edge of the tunnel/pinch first and work inwards towards the actual reverse light (from the lateral to medial). Follow the tunnel(s) slowly and apply more heat as needed. Be very patient and take your time.

a) Smaller bubbles will take care of themselves eventually. Focus more on not letting the vinyl fold over onto itself.





paid orders shipped !

 

still have more of these...red and smoke both available. lmk!

 

Thank you for the pics!! That lower tailgate is sick too!

 

Paid orders shipping in the AM! Lets see more pics you guys

 

If it ever warms up here I will put them on. This is unbelievable freakin freeze warning tonight.
Jim

 

Try to stay warm bud!

 

shipped a couple more today. lets see pics guys :-D (Those of you not freezing)

 

2 of these going out today

 

anyone else hate chrome?

 

Sure do....

 

Got mine super quick. Install was easy, little soapy water, credit card and i used a heat gun to assist with some bubbles. Came out perfect and the tail looks like it should have from the factory. Definitely recommend.

 

post some pics please :-D

 

Ummmmm.... how do I access the chrome on the taillight- got the taillight off and —- well- I’m dumb

 

Overlay.... it’s an overlay .... nevermind- got it

 

got it working bud?


paid orders shipped today

 

I did.... messed up a little and got some wrinkles but it’s all good- adds character