The GASSHOLE™ 2nd Gen Fuel Cap holder

I don't think so?

Took a little muscle to break it loose, but I've seen guys having to take a Dremel to create a slot for a wide flat head screwdriver to get it loose and then replace the screw.

I'm still using the stock screw and it took maybe 90 seconds to install. Hell, @boogie3478 went so far as to replace his whole fuel door.

 

We took advantage of a poor totaled Tacoma that was abandoned.

 

I know. I would have done the same thing. I just don't think mine was one of those 1000 ft/lb bolts.

 

I just went outside to test and see if I have one of the Arnold Schwarzenegger screws in my fuel door. Thankfully I have the pee wee Herman one. Now all I need is a gasshole for 2nd gen SB. Woosah!

 

Mine was in the soft side, so now that it passed the test, all I need is the Messo gasshole.

 

Got mine last week, screw was easy to get out. I have an aftermarket locking gas cap, doesn't thread into the gashole, but still better than nothing!!!

 

I know meso is super busy but I wonder if he is making anymore SB gassholes...? Or if he is just focused on lights right now. Hmmm.

 

I wonder what could be the difference between the third and the 2nd gen? Maybe the one for the 3rd gen fit with none or little modification on the 2nd gen.

 

Houston. We have a problem.

So, I dunno if this had been covered. But, The Gasshole seems to be designed for Tacos made after May of 2008. Those trucks have a spin on type gas cap shown on the right. The earlier trucks use the 1/4 turn type shown on the left. This style cap does not work with the Gasshole as designed. The tabs that engage the filler neck block it from penetrating the Gasshole deep enough.

I am going to try to modify my gas cap a bit by trimming up the tabs a bit. Ultimately though, I think this product design ought to be modified to work with both styles of gas caps.

 

Yes, it's been discussed in this thread, however Meso has not made 1 single reply about the issue. Here is what the solution seems to be.

https://www.tacomaworld.com/threads...-fuel-cap-holder.550925/page-16#post-18157268

 

Just notch it out with a dremel. It sucks having to mod a mod but eh its no big deal imo.

 

Did you have to modify that locking gas cap to make it fit?

 

Yeah, I didn't go through and read the whole thread. Just saw that they were finally available for my truck, got excited, and just ordered one.

Meso seems pretty busy messing with LED's and such lately. I think this product could be quite profitable for him if he could improve the design a bit and produce them faster.

 

No.

 

Fixed

 

What brand of locking cap do you have? My Stant is too small for my gashole

 

Thank god it was in my build thread..wasn't in my email.

$19 Gates 94-01 Acura Integra / 91-95 Legend Locking Fuel Cap, Black

https://www.amazon.com/Gates-31780-...&sr=8-1&keywords=gates+locking+gas+cap+tacoma

 

I'll get one if they make it for the SB again.

 

Sorry, been really busy with other stuff and haven't had a chance to address this or update the OP. It seems that Tacomas PRE-2008 have a retard cap. I haven't been sitting idle, in fact I already have a new design and was waiting for the tester to post up. @05Taco4x4 has the new one and confirmed fitment(post #345). I made it so there are slots on each side to accommodate the tabs in the cap.







If you have one that is the old style cap, PM me and I'll get you a free replacement for the slot style.

 

Payment sent for GASSHOLE 2nd GEN LB!