AZ Classifieds

FIFY

 

Oh I know

 

Yeah that too lol

 

No they don't. Don't do it haha

 

Who needs door hinges anyway?

 

Tube It

 

OR lube it

 

Always Lube the Tube

 

Idk why @Blender thinks that’s such a big deal. If you start hitting shit with a hammer, you’ll knock the door hinges out of alignment. So it’s much much better to just trim.



But if I had a blank 3rd gen to start over with, 285/75/17 Toyo M/T’s and a midtravel ADS setup

 

Think you could leave it at that? It would be just about ideal.

 

Maybe a long travel 3.5” kit haha. But that’s it

 

X2
Wheels just hold the tires on. Don’t need fancy shit

 

I do

 

After suffering with door closing issues. never again.

Unless it’s the passenger side then it’s a little funny

 

Fancy

 

****** SOLD ******

Ok folks, up for sale today are my old All-Pro front and rear bumpers. They were installed on my truck for 8 years and never once took any impacts or physical damage whatsoever. I had them stripped of the old thermal coating and had them freshly powdercoated with 60% gloss finish black inside and out for this sale. They are better than new, because new were shipped bare when I bought them and they had to be assembled.

-------------------------------
Both bumpers fit 2005-2015 2nd gen Tacomas

Front Bumper
These are the old-school version original All-Pro plate front bumpers that came in 3 main pieces that get bolted together. My powdercoat guy actually unassembled the whole thing and stripped the old coating out from between the 3 main pieces, put it back together, and powdercoated it as one piece. It's solid as a rock because of how many damn bolts go into assembling these, no matter what anyone says. All bolts/nuts are intact and now they are powdercoated over so you don't see any shiny steel anymore. I ordered this one with the center hoop, and there are 2 light tabs on the hoop itself. You use your factory 6 nuts for the front mounting spots, and I have the hardware for the frame tabs where additional supports attach. I have the spacer washers to level this thing out perfectly, too. You use your front large factory bolts that are already on your truck for the final 2 supports. This thing mounts straight and level and let me reiterate that it has never seen any impact. Not to mention this thing is super frigging thick plate steel, not that thin lightweight crap. The front bumper weighs 130lbs. 2 mounts for 3/4" d-ring shackles are welded on (no shackles included with sale).

Yes, this fits a winch. I had a Warn M8000 in it and there's room for a the controller next to it, too. I know up to a 10000 would fit. Holes are already drilled for standard winch mounting. You provide the fairlead of choice for the front.

--------------------------------

Rear Bumper
The rear bumper is one piece and weighs 80lbs. The All-Pro hidden hitch is required if you want to tow. I did not get their hitch. You use your own factory bolts for the install (6 total - 3 on each side of the frame). I also had this powedercoated inside and out and there is no damage. 2 mounts for 3/4" d-ring shackles are welded on (no shackles included with sale). You provide your own license plate illumination lights.

--------------------------------

I'm asking a firm $900 for the set, or buy them separate for $700 for the front or $300 for the rear. It would be a shame to split up the matched set, so I'll entertain separate sales if these don't sell as a set for at least the first week. I just spent $350 on powdercoating and you get to save hundreds on shipping and tax so this is a SMOKING deal. No low-ballers here, folks.

I'm on the northwest side of Phoenix, at approximately 67th ave and Happy Valley. You pick up, you haul away, cash only.

PM me for interest. I'll try to watch this thread as best as I can, but PM gets my attention much quicker.


How they looked installed on my truck (you can see the old thermal coat that was peeling off in spots) :






Here they are shiny new, picked up from powdercoat today (ignore the fingerprints and smudges from when I was unloading):

 

That’s a great deal. Hopefully someone with a second gen scoops those up fast!

 

Already getting PM's. I listed them on the AZ TW facebook page, too.

 

So much want! Just not in the budget! Damn