What Have You Done To Your 3rd Gen Today?

Had to drill nut certs into the roof. Never done something like that before. The toprac on the shell is bolted into factory installed channels

Edit:

Does anyone know if somebody out there is making and selling ladders that go on the halfdoors for accesscabs?

 

Removed all stickers, washed waxed and installed ditch lights

 

Got my Kings installed and AAL with 3 degree shims. While I was doing the AAL I also installed the U-bolt flip kit with timbren bump stops. I did the King coil overs last weekend. Truck truck drives great. I think in the future I'll swap to the OME rear leaf springs.

 

Overlays and will install a tonneau cvr tomorrow.

 

Thanks! 285/75/16

 

Drove it to go buy this today for the wife as a DD..................took it from the lot to the house to pick up the dog, then went to Big Bear. No Mall crawling here.
I did not get rid of the Taco

 

Do you have any side pictures?

 

Must have been tough. It was upper 90s and more humid here last week!

 

Fingers crossed too hopefully this advisor keeps up with the work

 

Used it like a truck today. Put down some grass seed and trimmed some overgrowth!

 

Best I have at the moment.

 

Does that rub? Did you lift it?

 

Thanks! Noticed that the 58-18 seemed to come up a lot more per some more reading. Is that aimed more towards the 2016 specifically? I guess I overlooked the 62-18 : /

Rescheduled for next weekend.

 

New interior mod, steering wheel Alcantara wrap!

 

Looks fantastic!!! What lift are you running?

 

62 mentions high elevations. I'd ask for 58-18. Explain to your service guy that your truck is doing all the stuff outlined in the Tsb and it's driving you crazy. They should do it for you.

 

What brand did you go with? Got a link?

 

As far as PITA I’d rate it easily 9/10

First wheel it was 105 in my garage about 2 hours after a grocery store trip. The wheels were still WARM (not hot) and it stretched the vinyl. I butchered a few stickers because it folded in on itself. About 2 hours later I had 1.5 wheels done and it was just ok.

2 weeks later.....

Jacked up and removed wheels, washed and laid them flat in my garage at night with a beer.

Applied beautifully, few bubbles, ZERO f* ups, 10/10 would recommend doing this method just for the frustration

I got them on Etsy. No instructions. Each wheel has 6 left and 6 right sections. 12 stickers per wheel.

Finished the other 3 wheels in less than 3 hours. 10/10 love the look. More durable than plasti dip and far less clean up.

I’ve dipped rims in the past and I prefer this method. It was a hard lesson to learn but if I’d of known I would have removed the wheel in the first place and saved a TON of fristration.

There are bubbles but supposedly they fade over time and aren’t very noticeable.

There is someone on here making new ones for the sport that will supposedly have double sided paper to aid with application

 

Well, it was a pretty busy week so far, I mounted rear floods, front ditch lights, a separate circuit to the bed running two 12v outlets and two USB ports (getting ready for a Dometic electric cooler). Replaced my fogs with the Rigid Kit, installed the pop & lock remote tailgate lock, installed the Genesis Off Road Dual Battery kit, installed the Switch-Pros 9100 using the PowerTrays bracket and Blue Sea Systems components, mounted the Panel on a SDHQ custom panel mount, installed the Cali Raised LED faux TRD Pro Grill, installed a Bak Industies X4 Revolver Tonneau Cover and finally got my Graphite TRD SEMA Wheels with Nitto Ridge Grapplers 265/70R17. Now time to take a little break and enjoy before the next set of mods!!!

 

What size is your baja rack? I have a smittybilt defender which is 54"x54" and I'm wondering which size gladiator net to get.

Edit: Nevermind. I think I found your dimensions: 48"x60". I think I'm just going to get their small version 57"x72" (4.75'x6') to allow for stacked gear height.