Switch Pros 9100 install and BS thread

Awesome, thanks for the great info man. I haven’t wired switches before but have been researching on TW a ton and am feeling more confident. I have the HAI harness and add on cable but still trying to figure out what wires to connect to what before I pull apart my truck lol.

I have both a powertray and a vertical SP mount on the way so need to make up my mind. What fuses did you tap into for power to the SP? Also what are you using the extra fuse box for?

 

The light blue wire calls for ignition. Which I tapped in below the power tray into the replay box with a mini fuse tap to the injector fuse.
The white wire is tapped into the same box under the low beam fuse with an add a circuit as well.
If you want to use the trigger wire for anything it is pink and you can use a mini fuse tap (add a circuit) for that as well to whatever you want.

The extra fuse block is for things not wired to the switchpro like my 12v bed plug, volt meter and bed light under my badrack and tent.

$6 Lumision ADD CIRCUIT BLADE STYLE ATT LOW PROFILE LP MINI FUSETAP FUSE TAP + 5AMP FUSE

https://www.amazon.com/dp/B00I0MWPXU/ref=cm_sw_r_cp_api_Q8I6Bb8P2K2MP
I cut a little notch under the lid to pass the blue and the white wires through. Going to hook the trigger wire up to the high beams to active the roof bar sometime just for fun.

*Disclaimer* I’m no expert so if anyone wants to correct me or criteqe me please do. Most of the stuff I learned on my wiring came from here and lots of forum reading and research.

 

Anybody know if switchpro will do a black friday deal?

 

Got mine installed today. Pretty easy install overall thanks to this thread. The part I was worried about was the harness for my air compressor and my air locker but they were stupid easy. Hitting my high beams and having all my lights come on is so worth it.

 

well i just realized my tacoma is missing the fuse puller .... interesting

 

Mine was too haha

 

So I followed your tap locations last night and they worked perfectly. But this morning I was having some issues with the panel not sensing ignition while driving. After some troubleshooting I figure out that tapping the 10A AC fuse only works for ignition if the AC unit is on. Swapped the Ignition tap to the 10A injection fuse and no more issues.

 

That’s a big bummer.

 

The panel wasn’t sensing the ignition? I’ve never had that happen. So you mean like you turned off your climate control and it didn’t work? Yeah the injection fuse works great too. I have that one tapped too

 

Yep exactly. Once I realized it, I tried with the climate control off and got no ignition (judging by no backlight and no light on the power block thing on the SP unit) then turned the AC on and got backlight and light on SP power block.

 

Hmm. I will have to check this out. I’ve never even thought about testing this out. I always have mine on but I may be switching locations if that’s the case. Thanks for the heads up

 

Also those wondering if you should get the harness for ARB Compressors, it’s completely unnecessary. You can simply wire power to the battery and then on the 4 blade connector the triggers go as followed.
Red - Air Compressor
Yellow - solenoid 1
Green - solenoid 2

So for those using just the compressor just connect the red to your desired SP wire and you’re good

 

What switch did you connect them to? I forget what the ckma-12 compressor draws.

 

I connected compressor to 5 and locker to 6. Not sure what they draw either but only needed one higher draw switch for my fridge and used the lower amp ones for my lights.

 

Anyone connect a Harrop E locker to their switch pro? I recently installed a front Harrop and ran the +/- directly from the locker to my switch pro. Figured you do not need the relay in the harrnes they send but does not seem to be engaging. See if anyone here has any tips or what to check.

 

well tapped into all the fuses i needed to do and appears to be working fine, now to add the lights, already put my CB into switch 1 and works fine

 

Bump

 

I highly doubt it. They consistently shut down group buys and other mass discounts so I would be surprised if they did offer a black Friday deal. The 9100 is worth every penny!

 

Kinda late now for BF deals but PolyPerformance has a Facebook 10% off code I recently used. $55 off but California tax got me at $36 so I only saved me $20. That $20 will go to the Ballast Point Sculpin I’ll be drinking during install this week.

***Couple days to ship also. Pretty quick.

 

I ended up accumulating $375 in Amazon gift cards through birthday gifts and other presents, so I was able to pick up an

$659 SP-9100 8-Switch Panel Power System With Concealed Mounting Hardware

SP-9100 for $174. About as close to a "Black Friday" deal I could get.

This thread has been a good read - helped a lot in terms of my thinking and setup.

I plan on using fuse taps for the 3 control wires. To verify:
Pink wire = high beam
white wire = low beam
Lt Blue = Injector

For the fuse taps, I am planning on using an ATM Low Profile Mini Fuse Tap.