Leveling kit vibration

so just finished my install on a leveling kit 2018 TRD sport 3 inch front 2 rear, haven't done alignment yet waiting for tires to come in but have a pretty good what seems to be driveline vibration. What do you guys usually run into with the leveling kits? Shim rear blocks to an angle? Front diff drop? Thanks!

 

So you're saying after you installed the leveling kit the truck now vibrates?

 

Whole truck or the steering wheel?

 

That was going to be my follow up question

 

Check and see if the rear blocks are installed correctly. The blocks possibly could already be shimmed, make sure there not installed facing the wrong way!! If the blocks are installed correctly rule of thumb is 1*deg. Of shim per 1” of lift !! Get Your Alingment Done ASAP!! If the truck vibrates in the front after Alingment put the truck in 4hi and if the vibration goes away while in 4hi it’s your needle bearing on the drivers side causing the vibration!! You will need the east coast gear supply bushing. Ecgs bushing!! This will possibly fix your vibration in the front!! Hope this helps

 

Yes after the install.

 

I will double check to see if the blocks are installed correctly, I did look to see if there was any angle or one side higher than the other and I didn't see any difference, possible I didn't look close enough though. I should be getting alignment done today, I was waiting on my tires to come in but I haven't driven the truck more than a few streets since then. And yeah it's hard to say if it's a vibration or more of a "shimmy" feel I know that's weird but that's best way to describe it. I'll keep you guys posted. Fingers crossed it's alignment or something I overlooked

 

Here is a link to the kit I put in

3"F+2"R Tacoma Leveling Lift Kit, KSP 3" Front and 2" Rear Leveling Strut Spacers For Toyota Tacoma 2WD/4WD 2005-2017, 1 Year Warranty

$105 KSP Full Lift Kits For Tacoma 2005-2023, 3"F+2"R Leveling Lift Kits Compatible with Toyota Tacoma 2WD 4WD, Full Suspension Kits Include 3in Front Strut Spacer and 2in Rear Lift Blocks with U Bolts

https://www.amazon.com/dp/B077M9S5Y4/ref=cm_sw_r_cp_api_i_IYqjCbTMJGHYM

 

3 degree shims for the rear leaf pack and or a carrier bearing drop kit for you drive line will help as well. With lift comes more problems that need to be addressed at the time of installation. Good luck hope one of these fixes your vibration problem.

 

Crap. Just saw that these are supposedly tapered. So if so is the high side go towards rear or front?

 

Rear, to decrease your pinion angle.

 

Did you get the problem fixed, or does it still shake?

 

I'll be surprised if they really are tapered despite the seller says they are, seems like it would have been pretty easy to see by pictures I'm looking at of what 3 degrees would look like

 

Rear bud

 

Hey guys appreciate all the help, blocks were BACKWARDS didn't realize they had a taper in in em. Shimmy shimmy is gone however will say there feels.like there's still something there. Alignment scheduled for Saturday and IL be putting in diff drop kit tomorrow. Hopefully that will take care of everything

 

Where did you get the diff drop?

 

Amazon sir

 

Not trying to thread jack, but it looks like the original poster had his question answer.
I need axle shims for my vibration, I have EL096R-P OME/Dakar. I'm looking at the Toytec TT3DS shims, but it says it needs drilling to work with the Dakar's EL096. Do I need to drill out the leaf packs center hole for the new longer bolt?
But it also says: "**NOTE- Use RS slotted shims for use with Toytec rear lift block kits or EL095/EL096 Dakar Springs."
But I can't find "RS slotted shims" It's confusing. lol here's the link to Toytecs site. Thanks for any help.

 

Didn’t quite solve it all yet but it is better. I had my blocks in backwards the taper going the wrong way and it obviously improved. I habe since dropped the front diff and added some spacers at the carrier bearing and it's Def better but still needs some modifications. Rather frustrating. I'm thinking I may also need some shims for the back and maybe play with the carrier drop height. This truck is picky!

 

I know the feeling. Mine's not bad, but it's not right. I think shims will do me a lot of good. I'm just going to buy the TT3DS Toytec shims. I see no reason it wont work on my Dakars leaf packs.
I think in order for shims to work with spacers, you need something like this below. But don't take my word on it because I'm not sure.

https://www.headstrongoffroad.com/store/p119/Axle_Shims_-_(2_degree_to_4_degree).html