What have you done to your Tacoma today? 1st Gen Edition

Install an oem radiator I had laying down and a transmission cooler

 

I love your truck dude, you should post a bunch of pics in the reg cab thread

 

Thanks man!

 

I give ya a hand man, it is quite simple. You are mechanical with cars. What i meant about not lining marks up. Is to do it before you release the tensioner. Also I will say replace all the pulleys and tensioners while in there. I didnt and now have a pully going bad. Im just waiting on a new radiator fan and crank pully before hand.

 

Them are some bad mamba jamba lights man!

 

- Installed ditch light brackets (still deciding what ditch lights I'm going to use)
- Threw the spacers back on
- Did an oil change
- Re-mounted the bumper lights so the covers can be taken off and put on without worrying about breaking them
- Fabbed an insert with nuts to make an attachment point for the front 3 bolts for the front skid plate to the Trail Gear bumper

And cleaned up the garage from today's work and doing the valve covers yesterday.

No pics you'll have to take my word for it... lol
But not a bad weekend's worth of work

 

I like these

https://www.ebay.com/ulk/itm/302855610453

 

I'm not sure if I want spot or flood for the ditch lights. And I need to have them covered.

Thinking about these.
https://www.ebay.com/ulk/itm/163053066580

 

Heck yeah !

 

Replaced cracked radiator with a new Spectra and while I had everything out I replaced the 3 belts, fan clutch, water pump, thermostat, and plugs.

 

...And then, a change of scenery. The Burr Trail continued south at this point to Bullfrog, a town we'd visit later on the trip - but we were headed east, towards the Henry Mountains - now seemingly so close we could touch them.

We stopped, to admire.

Check out the story and amazing photos at F.U.Rain Day 11 - We Follow the Burr Trail to the Henry Mountains​

​

​

F.U.Rain Day 11 - We Follow the Burr Trail to the Henry Mountains​

--- catch up on the whole story so far ---
[day 1&2] [day 3] [day 4] [day 5] [day 6] [day 7] [day 8] [day 9] [day 10] [day 11]​

 

Very Kool Man !!

 

Built a new reservoir to relocate my already relocated washer reservoir. Wish I knew about this style before but oh well. Plan is to free up the space on the fender well to put my air compressor there and not have to ditch my cruise control. Just letting everything setup for a couple hours before doing the install. Thanks to @cbechtold and @Blackdawg for the idea and info on this from their build threads.

 

This looks interesting. Where can I find more info on making one?

Thi

 

Scroll down just a bit: https://www.tacomaworld.com/threads...trail-rig-and-bs.159436/page-398#post-8802626

 

Anyone have a cure (besides replacement) for the dreaded lazy seat belt return?

 

Why do they have to be covered? I haven't had a cop say anything to me about mine. Even asked a few cop buddies, they state don't drive in traffic with them on they don't care. I forget the v.c. section but if they're not on, they're legal. And I recommend the vent visors, nice not getting soaked when you smoke in the rain..lol

 

That’s awesome. Thanks bud.

 

Auxiliary Lamps: Off-Highway Use 24411. Notwithstanding any other provision of law, a vehicle may be equipped with not more than eight lamps for use as headlamps while the vehicle is operated or driven off the highway. The lamps shall be mounted at a height of not less than 16 inches from the ground, or more than 12 inches above the top of the passenger compartment, at any place between the front of the vehicle and a line lying on a point 40 inches to the rear of the seat occupied by the driver, shall be wired independently of all other lighting circuits, and, whenever the vehicle is operated or driven upon a highway, shall be covered or hooded with an opaque hood or cover, and turned off.

https://leginfo.legislature.ca.gov/faces/codes_displaySection.xhtml?lawCode=VEH§ionNum=24411.

I've been pulled over for this is another vehicle for uncovered KC lights.

 

Before you install this thought id let you know you will have a good size air pocket because of the way the Y is installed. If you flip it around you eliminate the problem.
But here is a picture of where the air pocket will be formed.