*THE RTT Owners Thread (With BS)*

Yup over the cab. Most hard shell RTTs are super long and would hang way over the back on lower bed racks on short beds. I’d like to run a prinsu to deflect air over the tent as well as to carry stuff and have a light bar

 

I think @dziner had a hardshell over cab. 2nd gen though.

I don't know any 3rd gen guys.

I think there was a conversation about the hangover part. Someone didnt want 12" off the back. I cant remember though

 

Replaced the straps that collapse my CVT. Huge improvement.

 

link! Something I really wanna do to the cover straps too! I was thinking buckles instead.

 

Link below. Looks like the black straps are no longer available, but there’s blue and red. I originally planned on doing buckles, but these allow me to really put my weight into it and tighten the tent without fear of breaking anything. I’ve added a 2 inch memory foam pad so I really need to be able to tighten it.

Just cut the two ends off to size and screw them into the existing attachment points. Took about 5 minutes in all.

Edit: Now the link is below.

$17 PowerTye 1.5in x 8ft Special Edition Heavy-Duty Lashing Strap with Heavy-Duty Buckle - Made in USA - 300 lb. Working Load Limit - Blue - 2-Pack

https://www.amazon.com/gp/aw/d/B07KWHTTS6?psc=1&ref=ppx_pop_mob_b_pd_title&th=1

 

Thanks for the link. I just added a 2" memory foam topper under the original foam mattress as well and had to sit on each edge of the tant to get it to close enough.

 

Here are black straps in 4' lengths instead of the 8'.

$12 PowerTye 1.5in x 4ft Heavy-Duty Lashing Strap with Heavy-Duty Buckle - Made in USA - 300 lb. Working Load Limit - Black - 2-Pack

https://www.amazon.com/Powertye-Heavy-Duty-Lashing-Buckle-2-Pack/dp/B01MSE90ZM

 

So I order those 4' straps, went with red so that way they stand out and I remember to undo them before trying to open the tent... Just installed them today. I only got 2 since I only need them for one side, the end that doesn't have the hinges since that is always the hardest to get cinched down good with an additional 2" memory foam topper and my Tepui sleeping bad still in there. They work really good, much easier than climbing on the rack to sit on a corner and hope the velcro strap stays put.



They are riveted in place, with a small, 1" x 2" piece of aluminum sandwiched between the halves.

 

I'd be careful leaving it underneath if you don't have an anti-condensation mat. I wouldn't want the memory foam soaking up the condensation vs. the original mattress, since that one has a cover

 

Both of them get pulled out of the tent after a trip so they can air out. I'll have to look into getting an anti-condensation mat tho.

 

IMO I'd just swap the original mattress to the bottom and the memory foam on top

 

Well, when I was trying them out together in the house, I found that I liked the feel with the memory foam under the original. I'll see how it goes.

How thick are the anti-condensation mats? The one from CVT looks like about 1" or so, still looking around tho.

 

So what extra foam mattresses/padding are people using? I need a little more than the standard mattress provides.

 

Let me know when you want to camp. Im dying to get back out there since I got my truck back

 

I’ll go whenever man!

 

you have a tent now?

 

Not yet but I can use my ground tent until I get an RTT haha

 

Fishing derby this weekend. Camping on the ice. Plenty of room to join

 

This weekend @Arcticelf and I are installing hardwood floors in my house

 

Yup. About an inch. You'll want it if you do any cool weather camping

We have the tepui comfort one.... I'd say stay with egg crate or an air pad if you can. Or honestly throw a thick blanket under it.