Anytime Front and Rear Camera Mod

Need help so I have the anytime back up camera and got most of it hooked up but my kit came with a thick white wire that on one side says nav and on the other side connect both wires to switch what switch

 

Looks nice. What's it cost?

 

i ordered the germes and a couple cameras....got one that is made to go in the logo...used on tundras....thought it would fit in my grill around the tss bling belt buckle and it did not appear to work too well...so ordered that damn natika.

i see the difference with the natika cam - it appears you can use a bunch of nuts or different nuts...because the cable is smaller than most that come with the rca connectors already installed. when the nut is on the screw and i cannot get my nut off...because of the large rca connectors ...i cannot get the camera firmed up where i need it....

 

I went to the website but it doesnt have anyway to order it or a cost. I would be interested in looking into this, especially since I already have the front camera and wanted to install some side cameras in the mirrors.

 

I'm not really sure. I did some Google research but couldn't find the whole kit but the bits & pieces looked reasonable

Yea the mirror cameras might be kinda useful but the blinkers gotta be on to activate them. They do have a phone # listed at the bottom of their page

 

A grand

 

Anyone got any good tips for getting wires thru firewall?

 

Dish washing liquid. You can buy a chase from Harbor Freight for $9. Or buy a wire insertion tool:

$9 Performance Tool W2935 Stainless Steel Wire Insertion Tool - Piercing for 1/4" Wiring Hole

https://www.amazon.com/Performance-...C0B2GP9P9DN&psc=1&refRID=XXS3PFJRSC0B2GP9P9DN

 

Still need to do this, and I'll likely be relocating my rear camera due to swing out once its done and installed.

 

Good idea on the dishwashing liquid. I had a hard time getting the wiring through the grommet. I used the long, probably 12", #2 craftsman screwdriver to punch the hole and then used a straightened wire coathanger with the sharp end twisted 180 degrees and wrapped the wires to the coathanger with electrical tape. It was more difficult than it should have been. I'm sure the dishwashing liquid would've made it push through much easier. Also, I had ty-wrapped the wiring together about every 6" beforehand and considered removing the ty-wraps before I pulled the wires through the grommet but didn't and they pulled through just fine. I routed the wiring over the steering wheel column before pulling them through to the radio and, since there was plenty of extra wire left over, I wrapped them into about a 6" loop and ty-wrapped the loop. After seeing others do this job, I thought there would be more room left and the radio would have sat in the recess more easily. It took the mounting screws to make it go all the way in. The next time I go back in, I'm gonna try to move the wiring around some. Maybe attach some of the wiring to sticky backs and attach them above the radio. We'll see once I go back in.

 

is there another source for the 3 way toggle switch ? they are out of stock

 

They have been out of stock for quite some time.

 

Got mine installed today! As others have stated, getting the wire through the firewall was a real bitch. Tight working area and you just need to be pretty aggressive with it. Also stole some inspiration from a fellow member as my OCD made me take a dremmel to the TRD pro grill to occomidate the front camera in the center. Couldn’t live with installing it off-center lol. Since the grille was only $75, this gave me more confidence. Also could have just bought a flush radar sensor cover, but that’s less fun.

 

Looks good but now it makes me wonder where people are putting the camera with the sensor plate. I'm one that has to have it perfect. Lol

 

If you have a sensor plate, I bet it can go over it without affecting the sensor.

 

This is what I did. Works fine, no issues.

 

Can you post a pick of the camera? TIA.

 

Sure. Won’t be for a day or two. Out of town.

 

Finally got my backup harness installed from , and everything works great. I'm a little sad I didn't get the full kit - going to upgrade as soon as the front harness comes back in stock.

 

Here you go.