What Have You Done To Your 3rd Gen Today?

I’d like spare aswell

 

Yup. They were on the truck when I bought it.

 

Be sure and post the after pic with those new leafs. I’m curious to get that exact setup in the rear too

 

I think I seen a similar set up and it was super high .

 

How are you going to install these? Also a tip for you. 303 Aerospace works great on the tonneau. Keeps it like new.

 

Super sick truck. Must say them MGM’s look good. Btw how do you like the feel of those king shocks? How much lift do u have front and rear?? I’m guessing you had to do a CMC with those tires. One more question how much was the total cost on the suspension?

 

Your very welcome

 

Those atlas rolls are the shit

 

Love the new Meso fob! That said, You may want to double-check the orientation of your bottle opener...

 

Thank you!

 

Gave it a wash, a much needed vacuum and applied 303 to the tonneau cover and the interior. 303 works great on the tonneau cover and on the interior. Helped hide some of those interior door scratches on the drivers door. I tend to get the door with my foot when I’m getting out. Don’t see how as I’m only 5’ 3”. It seems the Toyota plastic scratches easy.

 

Love the truck, but you need 100 foot shoulder to make a u turn on the road(or at least my old one did).

 

Finally wired my cap/shells 3rd brake light, only took me 6 months

I didn’t want to tap into the factory harness so I knew that when I got the totaltail stage2 that’s what I’d tap into. Made up my harness and added another power/ground for future dome lights.

When I get ready for the domes I’ll tap into the 2 wires that run into the drivers tail and run it to the battery for anytime power.

I want to get a Deutsch 4 pin connector. This is where I fished the harness out, there is a small gap but the harness was thick so I put a 18” flat head behind the metal siderail/lip and opened up slightly. I also took the 10mm bolt out of the top of the total chaos stiffeners Hoping it would widen the gap but it really didn’t. I’ll probably shape the lip back in but leave enough to not pinch the harness.

Ran it through the hole there. Might look into a grommet but not sure if it will work, it was a loose snug fit as it was (if that makes sense)

Ran it behind the bracket and under the taillight harness in the mounting clip on the actual taillight (yellow arrow). You can see the red/black wires that I’ll add to for the domes.

I removed all the cloth tape for that connector so I could put on an adhesive heat shrink (never leave it close to where your going to solder… ask me why ). Traced the blue wire to Meso’s harness and cut the wire, slide heat shrink on and solder. Do the same for the white/black stripe. Blue to blue, black to white/black stripe.

Connections done and sealed.

Re wrapped Meso’s harness with cloth tape.

Temporarily connected until I can get those Deutsch connectors. You can also see that bolt I sheared off on the top of the total chaos stiffeners edit: the bolts for the taillights look exactly the same as the one I sheared off and the pt# for those are
Tail Lamp Assembly Bolt - Toyota (90119-A0079)

And done… now I need the Customs in @MESO that 3rd brake light can be so much better. My birthday is coming soon and I’m ready to be the next creative project.

 

Now that’s funny. Market adjustment my ass. The TRD Pro’s at my dealership sit there for a while until one of the managers use it as a demo.

 

Will do! I am adding a Four Wheel Camper so my setup should sit about 1 inch above stock ride height with my Icon Stage 6 front coils with 700lbin springs and the stiff rear leaf setup.

 

Kings ride amazing. I'm currently running the comp adjusters at full soft in the rear and 4 clicks from soft in the front. I'm not sure on total lift since I didnt measure before adding the kings but my current hub to fender measurements are front 23" and rear 23.5". Currently it does not have a CMC but it needs it. Suspension cost was right around $4k

 

not warranty. i haven’t got prices yet.

 

Matching wheels and tires


Bed liner on the lid

 

How many miles on that filter ?

 

I can't wait to mount the BFG K02's on these Stealth 6. Got an appointment at the tire shop on Monday...