What have you done to your Tacoma today? 1st Gen Edition

Nice job! Dirty is easily cured by renting the "Rug Doctor" I cleaned mine up.

https://www.tacomaworld.com/threads/rented-the-rug-doctor.612516/

 

Installed new diff lock actuator and did the grey wire mod. Works great.

 

Next will be the diff breather tube mod.

 

This is from a few days ago. I installed a 30 inch lightbar from superbrightleds behind the bumper.
https://www.superbrightleds.com/mor...30-inch-off-road-led-light-bar-90w/3671/7633/

 

Lookin good looking good

 

Do you have a boost cut on your SC?

Getting ready to install a AFR with boost cut solenoid but all the information I have found is for turbos

 

...a little over 4 miles after we'd started, we crested the ridge holding back the lake to a view that's worth every minute of the climb. (And descent! - if your knees don't kill you on the way down - )

Full story and photos of it all - Colchuck, Cherries, and Chainsaws





​

 

That bottom pic is worthy of framing.

 

There isn't really a good way to do boost control for a SC. Thats what the pulley is for mostly. There is a bypass valve you could use but Im not sure how effective it'll be at regulating the boost on a blower.

Why do you want to do that anyways?

 

Yessir. I usually call it bank 1 sensor 1 or the AFR sensor. Everywhere online they were referring to them as upstream & downstream. So I figured I'd get a quicker response calling them that. Which exactly what I got. Thanks @eon_blue !

 

You can use the bypass but it won't control boost as much and release it (either on or off). I've seen a guy use it with his twin charged setup; to open when the turbo was spooling.

@Rldanie boost is generally controlled by your foot as the S/C builds boost linear with your engine speed. Pulley's will change how quickly boost builds and what you max is. Turbo's are exponential and need a waste gate to control boost.

I think some of the snail type chargers (Rotrex) have a more complex drive that allows somewhat non-linear boost profiles but still not exactly "boost control".

 

I don’t know why you think you need a boost cut solenoid. Positive displacement superchargers do not need them. They use a sized pulley for target pressure and a bypass valve for idle and cruising.

 

How does a blower regulate air? I'm assuming once target psi is reached there is a bypass. Where does that air then go since the maf accounted for it?

 

Here you go - Denso only

EDIT: below sensors are for auto trans.

Upstream AFR Sensor -
Denso 234-9001 Air Fuel Ratio Sensor -https://

$149 Denso 234-9001 Upstream Air Fuel Ratio Oxygen Sensor with 10.6” 4-Wire Harness, for Auto Trans Equipped Vehicles

www.amazon.com/dp/B000C5WD2Q

Downstream o2 Sensor -
Denso 234-4189 Oxygen Sensor

$70 Denso 234-4189 Oxygen Sensor

https://www.amazon.com/dp/B000C5YCRA

 

Those ones show as being for the auto trans, the wiring is different length for the manual trans Tacomas

Don't know why they made them different lengths but for some reason they are, I initially ordered the wrong rear one awhile ago and had to exchange it

 

Blower speed is linear with engine speed. Your max boost is only achieved at max engine speed. Therefore, when you are getting a blower, you need to get a proper sized pulley to meet your desired boost. Once installed, you will never exceed the mechanical limitations of the ratio between your engine and supercharger so no danger of over boosting. To my knowledge, there is no boost control for blowers (or any supercharger).

Turbo's need a way to control boost as the turbo spools exponentially with the engine speed. This is why turbo's are superior to superchargers; they spool to your desired boost level much quicker in the engine's power band (as long as you pick a properly spec'ed turbo).

The bypass valve just allows air in front of the supercharger to bypass the screws and go directly into the engine without being pressurized. This is only done during idle and low engine loads as the supercharge efficiency is too low in this range.

 

Another reason I don't understand why there is any advantage to a blower over a turbo. If you can install a blower I'm sure you can a turbo.

 

@eon_blue Hey bro, quick question, can you post the link to the door handle that you're always talking about? I know they're aftermarket but I don't just want to get anyone. I need to replace my drivers side if that helps. Thanks!

 

Turbo is a bit more complicated to install than a blower, especially 1st gen blower (no intercooler).

When it comes to performance, Turbo > Supercharger

 

It was the Dorman one, I got it off Amazon...both sides have held up for the past 1.5 yrs since I broke several OEM ones lol.

$34 Dorman 79344 Front Driver Side Exterior Door Handle Compatible with Select Toyota Models, Smooth Black

https://www.amazon.com/gp/product/B001NYN8S8/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1

The Dormans have the bigger lip on the back that engages the handle which keeps it from slipping off like the OEM ones do, at least that's how mine were failing. Seems there are numerous ways the door handles tend to fail so YMMV.