What Have You Done To Your 2nd Gen Tacoma Today?

@Kidwidataco @inesshell @trrubicon06
I had a bmx bike I hauled around in my 1st s10 & my 92 blazer. I did mostly dirt jumps, homemade ramps & some mild flat land. Had 2 different sets of wheels depending terrain. Had a yellow haro revo which only frame ended up being stock when I sold it to a friend & free agent hellcat that I gave to my nephew cuz I wasn't riding as much.

 

Well to be honest, I had to pick up my daughter at the airtport at 5am, so I was already up and took advantage of the opportunity/timing.

 

What front bumper you have? I dig it! Like the way the fogs are recessed into place.

Well @ least I have the cmc plates. Any trimming on fenders etc like on 35s?
I'm thinking bout eventually keeping size I have now (265/75 16) as normal street & having maybe these for wheeling if ya know what I mean. After all it is my daily driver too... approx 30 miles a day.
This is what I just hit today after getting home from work. I'll hit 70k on way to work in 5am

4popper FTW!

 

So after installing an OME suspension my driveline started to make noise. Despite OME techs recommending the suspension I bought for the winch, ARB bumper etc. it made the driveline angle too steep. I made it a little better with shins but it was too steep to correct. Greasing the yoke helped because it would fill in the splines a bit but it was a temp fix. I went to a local driveline shop and had a custom driveshaft made. This one can accommodate up to a 26 degree change. So I put it on this morning.

 

Man I commend you for saying.. fuck it I’m up and I’m going to get this done with now.. @545 AM. I’m snoring my ass off with my girls at that time.

 

What OME setup did you install?

 

Salex console organizer. Shoulda done this a while ago. I got the glove box organizer right after buying this truck in 2015.




Also got the PopNLock in.

 

use a deburring tool on the edges of the organizer. your knuckles and the back of your hand will thank you. mine was really rough.

 

Mine didn’t feel that bad actually. I ran my fingernail across the edges and it was relatively smooth. I think my glove box organizer had rough edges though.

 

Wheels and tires this week.
Method 701 17"
Nitto Terragrappler G2s 265/70 10ply



finally got the flares trimmed and back on

 

Who died under your diff??!!

 

a whole quart of a red wood stain. it landed upside down and did the whole card under the glass of water trick....yea no..didn't work.


that was the project

 

You should do a chalk body outline as a cover story.

 

Link for organizer?

 

salexorganizers.com ?

 

Meant molle panel organizer. Thanks though!

 

Thanks

Without a lift/leveling kit its gonna squat a lot in front. Do your self a favor and go with synthetic line for a bunch of reasons but one ia weight reduction.

My bumper probably weighs 2-300 lbs i think. and the winch weighs around 60lbs then add another 30ish of steel cable and shackles... She'll squat.

As far as driveability, id have to drive one without a front bumper to see. You might see a slight fuel mpg decrease, maybe. other wise it handles fine and i dont rub on anything. I had to trim my inner fenders towards the bottom of the fender nafter my diff spacer. Tires rubbed.

 

Whats nerf mean? They can only take hits from nerf balls and darts?

 

I decided in the mean time before i order a new fancy console, id paint my stockie black.
Then i cleaned vape residue off my windows using goo gone and windex with my little buddy helping ...

 

6 miles late but.....