BUYER BEWARE: 2nd & 3rd Gen Tacoma In-Cab 120vAC 400W Anytime Power Outlet

I’m about to get some shut eye but I will get back to you in the morning with what all you need

 

Thanks! I am in and I’ll pay then also let me know what shipping is. 92009

 

I have 60 PMs that I am still sorting through. I get through 20 and then I wake up and it’s back up to 60. It will get there. If you have PMd and have followed the payment process with sending me all of your shipping information and full name, I will get everything updated that you have made your payment. I promise.

 

Also does this leave the bed outlet at 400w all the time when engine is running?

 

Looks like that outlet was designed for that location.

I can see one going in that spot passenger side along with rear center console.

 

Thanks for the update! Nothing like a desired product to keep you busy.

 

I’ve been playing around with this and I’m thinking the only way is through the dual battery system but I’m still working on it. The only way I’ve done it in the past is ACC mode. I’d like to have this as well. Stay tuned

 

My plan isn’t to have a batch at all. Once I get these I will have enough to ship them all out at the same time. Everyone will get them at the same time. So everyone can pay now

 

This has made it difficult. I’m not going to lie

 

When someone sees that this switch is in stock can someone pm PLEASE let me monkey. It has been out of stock FOREVER!!! I plan on getting this mod but only when that switch is back in stock

 

UPDATE:

I also wanted to let you guys know that I had to make an adjustment to the length of the PNP Harness for the AC Power Outlet Harness that originally was set at 12”. When I did my personal install, I have seat heaters that are installed as well under there and when you run your wires you MUST run them underneath the bracket due to the 10mm bolts that you use to anchor your Center Console down with in the middle. Otherwise, you will end up smashing your wires. Please please do not forget this step when you install this. However, when I did this, I ended up being about 5” short.



Therefore, I extended the harness from 12” and I have decided to make them 20”. Most of you probably will not have anything here and will have it completely open so you will not have to go to the side where I had to go. However, for those that may have some things, I did not want to take that risk, so I wanted to make sure everyone was covered for this install. I think 20” should cover this location for this Power Outlet.

Anyways, I just wanted to share my findings during testing of my install and why I like to personally install it prior to releasing first.

 

Thanks a lot for the info. Are there any videos or information about doing it via the battery set up. I would prefer not to go that way if I didn’t have to but still would like to read up on it.

 

I actually have a diagram but before I release anything I want to wire everything up on my truck first and test it. Which I am planning to do after release and after I get all my IN-CAB OUTLETS Installed. Once I know it is good, I will release the Wiring Diagram and any PNP Harnesses I create for others to purchase for the REAR POWER OUTLET CONSTANT POWER ANYTIME MOD

 

UPDATE:

What do you think? I wanted to do something different and I noticed the Tundras have a storage compartment here so I wanted to install something here on my Tacoma





A closer look at the inside...

 

Tell me more about those bags... Do you have a source for them?

 

https://youtu.be/XdvNoUq5b-o

 

https://www.blueridgeoverlandgear.com/products/taco-tray-tacoma-console-organizer

Wow, that's way better than I was expecting, thanks! I need to get a set of those, but now I'm browsing their site for other things I "need".

 

The even better thing is, the Taco pouches fit a variety of places perfectly in our cab. They fit in the middle console, glove box, and in our door cubbies.

 

HOT DAMN !!!! Thats great to hear!!!! Thanks again