DFW BS Thread : ********NEW MEET!! CHECK POST #1*******

I looked at them but to old to change now. I will keep my stick burners

 

3rd gen mgm, lift, sliders or steps, raptor lights in keller about 7:30 off Whitley. You here?

 

Looks so good

 

Thanks.

I’m really happy with the color choice.

 

Pellet smoker?

 

Yeah, Blaz’n Grid Iron.

 

Not familiar, I'll have to look that one up. Pellet smoker has been on the want list for a while.

 

I recommend them. Very solid built units. I would avoid Traeger. I see FAR too many have issues, catch fire or fail prematurely.

 

Went out with Jeff (@Stoked ) to Northwest OHV.

We had a blast.

Jeff's son drove and so did mine.

Do it!
It's Easy.


Ut Oh!


Backing out of something that was just a bit too much.
The previous one is where I had to use my strap for the first time. I didn't get stuck there but Jeff high-centered above that and we had to pull him out.

I'm glad we both brought recovery straps. I had to back into that to pull him off of the high-center.

The pic blow was a "nuh-uhh" moment and we both backed out.




My son driving.

 

At the time I was looking hard rec-tec seemed like the best bang for the buck.

 

Damn toyotas holding up the trail

 

Hope everyone had a great Holiday weekend. This was our 15th annual dove hunt down at the ranch, so we decided to do a little something special. We went old school and decided to blow something up and giggle like little boys again.
We took 6 pounds of tannerite, 1 clay fire pit, 1 55 gal blue water barrel. That turned out to be a pretty good combination.
We filled a bleach bottle up with the 6 pounds of tannerite, and set it inside the fire pit, and put the water barrel on top of it hoping the flume of the fire pit would channel the energy upward. Well... it did, and the barrel was torn up.
We set it at 250 yards, and then put a camera at 100 yards from the set up to catch a better angle of it. Even 100 yards away, you can see the camera tripod wiggle from the percussion of the blast.
The tannerite was hardened from being in the container for a year. so we had to dig it out and smash it up. My buddy was giggling as I took the picture because I told him it looked like something out of Scarface.







So here is the video... first from the bench (250 yards away). Next from a tripod and 100 yards away.
If you listen close... you can hear the crack of the bullet fly by the camera before the explosion.

 

Howdy fellers, been MIA for a while. Work and the boat have been keeping me stupid busy. And since I didn't think I have enough hobbies- I've decided to get back into vintage motocross. I'm about 80% done restoring an '81 Husqvarna 390CR.

 

Welcome back!

We’ll need pictures, of course.

 

So how long should I expect for a new set of OEM pads and rotors to bed in and get to feeling like the old ones before I start wondering if there's something not quite right? I leave for the mountains in like 2 weeks and need these stoppers to be on point by then. Initial bite feels about in the same place, but the power in the first bit of pedal travel (and beyond) just isn't what it was.

 

It shouldnt take long. Did you break them in? Do you need to bleed them to get air out of the lines?

 

A little under two months away...

Who is going and where we camping?

 

Hmm I can probably make it fri-sat. Not sure if I would be able to camp sat night since i work on sundays.

 

I’m looking to replace my front wheel bearings does anyone have any suggestions on brands to use or ones you’ve used before???

 

There are a couple of people on here that sell them pressed together and everything. Check the main classified section for them.