3rd Gen Tacoma Power Folding Mirrors

SR5 Power Window Regulator Connector One wire has 12Volt power when the windows are raised up and the other wire has power when going down. Unsuccessful in finding constant 12Volt Power in the door. Did find Acc. 12VOLT.

 

Just received the adjustment brackets today which was the last of the kits. Putting them today now actually. I was trying to wait until the install video was complete so that everyone has that to go off of. I’m thinking maybe the middle of the week to end will be when I will shoot to ship and officially release

 

Did you go through all the wires yet for me?

 

I found Acc. Two places, large white wire in the main connector for the windows not (pin 13) and small white wire in the door lock connector. Note: I’m surprised no one mentioned there is no 12VOLT or ground behind the plug and play connector for the tailgate opener and module. Was it pin 9 ?

 

Same here. I cannot find constant 12V with the key off and I checked the harness that goes into the switches, the harness that goes into the mirror controls, the harness that powers window motor (as you mentioned), and the harness towards the door latch...left side of open door.

I cut the red fused wire from the PNP harness, that lead to window motor. Connected red wire to a wire that I ran separately as a constant 12V, from door to dash fuse box.

I am still hopeful of a fix or PNP harness.

 

Finally another SR5 owner, I had to do the same. Did you get the black,green,white pins to work on your connector ?

 

Yeah.





What do you mean there is no 12V or Ground behind the PNP Tailgate Opener and Module?

You might want to check this too because I noticed that depending on whether trucks have Power Window (w/Jam Protection m) or (w/o Jam Protection) depends on which Pin there 12V ACC is as well. It is either #9 or #10.

You can see where the ground is located in the Harness. That is obvious

 

Can you check any of the wires in the door. It doesn’t just have to be the ones that are in the current Power Folding Mirror Harness. If it is in the door and it has an OEM Connector, most likely I can make a PNP Harness for it. I’d like to get this done prior to release if at all possible please.

 

Which ones are these?

 

My truck must be W/Out jam protection because there is only two wires. As I mentioned there is 12volt Acc.


If you are referring to folding mirror pnp harness or the tailgate plp opening harness

 

Lone white wire the two wires from the mirrors green - black

 

Well in that message it was referred to in it about not having a ground or 12V for the Tailgate Opener and we do in the Harness so I was showing where the Pin locations.

 

I’ll double check but I don’t think there is on chassis side

 

Pins 1 and 9

 

Lone White Wire taps into ACC wire in Power Window Connector for SR5.


Green and Black go into the O1 Connector like this

 

Yes I know thank you, i had trouble with the pins as if the wrong size even with jewelry screwdriver.

 

If you need some, let me know. I have some I can send you.

 

@JohnnyReb I did get those three wires into the OEM connector. I'm not an electrical person, but I have some tools. There is a tab on the original connector that I lifted, then I inserted the wires, with pins, using a jewelry screwdriver. I tried to compared the configuration before inserting and I had to go back and reinsert. I felt as if those 3 wires were thin and fragile at the pin connection. Use caution and don't force.

 

Exactly this. There is a right and wrong way the crimped end will fit into the housing. There is a little tab that sticks up in one face, that slides into a keyway in the housing. Below is part of a conversation with another member that was going on when we did our installs. If you have it facing the wrong way, it will start, but not seat completely. Then, you will not get a connection when you plug the housing back into the mating connector housing. I chased this very issue for a few hours.

CAUTION: make sure you put the crimped ends into the connector facing the correct way. The rolled ends of the crimp should face away from the latch. There is a small key on the crimp that will not allow the wire to fully seat if the crimp is not facing the right way.
You may need a jewelers screw driver or eyeglasses screw driver to finish pushing the wire all the way into the connector.

 

Thank you very much everyone for your help and suggestions I’ll give it a try