What Have You Done To Your 3rd Gen Today?

It's likely eating the e-coat off the cab floor under the carpet

 

Washed and waxed.

 

Could be, but I got rid of that truck last year, and at that time, it was already leaving chunks of body and chassis parts behind in parking lots. So, probably didn't make a lot of difference.

 

Did you just 3M the moldings? I want to take mine off, but they removed the tiny front clips when they installed it. I've had a hard time figuring out if you really need the clip. Thanks!

 

There are two separate coaxial plugs leading to the shark fin (FM and XM are built into the shark fin). Some folks are making a flat shark fin replacement, but for now, I opted to use the old stubby shark fin from the older tacomas. I lost FM reception, so I ended up plugging my shark fin directly into the back of the head unit. More on that here, here and here

 

Thanks for the links. I did read those posts, but had trouble putting them together in my mind. I'll have to back and re-read.

 

We've used the Graco click connect system and it works pretty well: http://www.gracobaby.com/en-US/Infant-Car-Seats

You can get a base for the car/truck and stroller that that seat locks into. It allows you move the infant seat without taking the kiddo out of it. The base with the seat can fit in the middle of the back seat of the double cab Taco.

 

Based on that I have another 64,000 miles left on my factory brake pads on my 2016. I guess I will need to inspect my pads sometime in 2028. Just to be safe I will have a grandkid do a spot check for me in 2026. Good to know.

 

Gave her a nice bath and some protectant... She was looking rough, wish I had before photos.

 

damn... nice shine!

 

Thanks! Chemical Guys Butter Wax! Came out better than I thought it would, pretty impressed with their products.

 

Don't know if this has been mentioned before, but found the dimensions for this ammo can, match up pretty well with the cubby hole behind the driver's side rear seatback. I'll fill this with some needed tools.

 

added the

$17 Tekonsha 3031P Tekonsha Trailer Brake Controller Harness, Compatible with Select Toyota Tacoma, Tundra

Tekonsha 3031P wire harness and install , no cutting required.
I did add a section of pool noodle to hold it nicely inplace.
note: unit shuts off 15 minutes.

 

Added a clip for the MAF wire on my CAI tube. Didn't trust the adhesive, so I added a zip tie as backup:

$7 Viaky 30 Pcs Black Clips Self Adhesive Backed Nylon Wire Adjustable Cable Clips Adhesive Cable Management Drop Wire Holder

https://www.amazon.com/dp/B01M6U9Q9C/
https://www.amazon.ca/gp/product/B07J2F5L4J/

 

Once I spilled a bottle of Mop n Glow in the back of my car. Smelled like a new car for 10 years.

 

1) Make sure to put a large towel under the car seat. Trust me on this one.
2) You will eventually find Cheerios in places you couldn’t imagine.
3) Oh yea, infant human vomit is like acid.
4) And I wouldn’t change being a dad for ANYTHING in this world.
Good luck!

 

Made a couple of filler pieces for the gap below the headlights. I used a GrillPro BBQ mat P/N 72596, a bit thin so the lower edge turned out rumply. At some point I'll make another set when I find some thicker rubber mat material.

 

Great tip here. Thanks for the info. May have to make a trip to HF.

 

Smart move

 

Well for one thing it doesn't stick out 3 feet in front of the truck like yours.

Besides, where am I going to find a Pelfreybilt aluminum bumper for 3rd gen?