Cam gears for V6. Add power AND mpg

By the looks of it, any extension or socket would hit lip of the head itself. A wrench with an extension should do you solid

Also spark plug removal is likely to aid in making it easy to turn the motor over, I was going to try it without removing spark plugs first.

 

Figured there wasn't a way around it. Thanks for confirming, fellas.

 

Looks like parts numbers for gaskets are

• Right (passenger) Valve cover gasket - 11213-AD010
• Left (driver) Valve cover gasket - 11214-AD010
• Surge tank (upper intake) to lower intake plenum gasket - 17176-0P030

Things one might consider replacing while in there.

• PCV Valve -
  $13 12204-31030 Toyota 12204-31030
  12204-31030
• Others items???

Doesnt look like there is a part number just for the throttle body gasket not that it would be needed or hard to replace.

I might even take the time to check valve clearances while i have her opened up.

 

No room unless you pull the front cover which adds loads of work

 

The PCV valve is a stupid simple part. You can just clean it

 

Thats what i figured as well, pull it out, brake clean, call it good.

 

Those part numbers are correct. I picked them up yesterday and verified.

 

Has anyone with a 2012+ done this that has the SAIS on their v6? If im not mistaken the SAIS valves are bolted to the passenger valve cover, how much disassembly is needed there?

 

I did it on my 2014. You do have to take some of the SAI off, but it's not hard. Totally doable. Also, a crows foot makes life super easy when you're trying to get the cam bolt off.

 

thats what i figured, nothing but a few more non critical nuts n bolts.

I was thinking id grab some Flare Nut crows feet so that there is more engagement with the bolt head itself vs open end crows feet.

 

I had a Harbor Freight flare nut wrench break once. It woulda been a pain if the broken piece fell down into a cam chain tunnel.

 

What size crows foot is needed?

 

17mm

 

Thank you.

I will be ordering a set of these very soon.

 

Ill assess beefieness of flare nut vs open end options at HF when i have them in my hand.

 

Just stick a piece of pipe over a regular 6pt socket wrench.

 

Id probably do that to get it off (but with a wrench - dont think youd be able to get a socket and ratchet in there)

Its more for torquing it down properly on reassembly.

 

Oh, yeah I didn’t know you can’t fit a socket wrench there

 

OK, getting all the info I have researched in one place, figured id share it here as well

Replacement Gasket part numbers:

• Right (passenger) Valve cover gasket - 11213-AD010
• Left (driver) Valve cover gasket - 11214-AD010
• Surge tank (upper intake) to lower intake plenum gasket - 17176-0P030
• Throttle Body Gasket -
  $13 22271-0P010 Fuel Injection Throttle Body Mounting Gasket
  22271-0P010

Torque values:

• Cam Bolts - 74 ftlb
• No.2/3 Chain Tensioner Assembly bolt - 14 ftlb
• Valve Cover
  • Outer Bolts (7x short) - 7.4 ftlb (88.8 inlb)
  • Outer Nuts (2x) - 80 inlb
  • Inner bolts (3x long) - 80 inlb
• Coil Pack bolts - 7.4 ftlb (88.8 inlb)
• Surge tank (aka Upper intake) to lower intake (2 nuts, 4 bolts) - 21 ftlb
• Surge tank stays / throttle body bracket bolts - 15 ftlb
• Throttle body bolts - 9 ftlb

Optional Stuffs:

• PCV Valve - 20 ftlb

 

I exploded my HF 17mm crows foot trying to get the cam bolt off. Was very glad I stuffed paper towels in the timing chain area and it caught the broken piece.

For tightening, I went as tight as I freaking could, because it took all I had to get them loose in the first place