Colorado Trading Post

Sure.. I'll do it a little later if that's ok

 

Throwing on my OME 887+5100's 3in lift this weekend, Ive already done the full 3rd gen-2nd gen sus swap, but first time doing UCA's (spc's) and curious if anyone would be potentially available for a 'facetime troubleshoot' if I run into any crazy issues?
I currently have the SPC's set to +3deg or the "C" Position from the chart in the instructions based on some of the posts that other spc users have mentioned with similar lifts and tire setups.
4runner Trail edtion wheels 265/70/17's currently 4.75in back spacing, but trying to find some 285s with a black friday dealio here in the next couple weeks.

 

PM'ed you but you might have better luck with this type request in the BS thread.

 

I am interested in the window. Does it have the motor with it or it is just the glass?

 

My experience

It is easier to install the struts while the UCA is off. I put antisieze on the thru bolts. While you are there, might wanna put antiseize on your LCA thru bolts too.

My settings

I have my SPC set at +3degree and then continue to adjust with LCA eccentrics. I have about +4.75 total. I am a tad bit forward so I will probably aim for +4.25-4.5 next time i get an alignment. I have 285/70/17.


Have Fun!

 

Can't believe no one has snatched up those drive shafts. That DC joint is worth $100 by itself, and someone could keep the 1- piece thin walled one as a spare or re-tube cheap. If I didn't already have a DC and a spare I'd be all over it.

 

@crolison Dibs on the dash trim piece. Can you PM a photo so I can verify?

 

Looking for a set of bolt on sliders for my 2015 TRD OR DCSB, preferably DOM steel.

Also interested in a mid height bed rack, KB Voodoo/Max Modular, CBI, RCI etc. that can be modded somehow to work with my tonneau.

Also selling my 2.0” rear pro comp shocks which are good for up to 1.5” of rear lift and a 1” rear lift block. 10,000 miles on them both, prefer to sell together. $250 OBO (retailed for $400 for the set new)

 

I've been looking for this! I'm down in Salida. Any TW Express headed south?

 

I’m headed there the 19th and I live right by @olas if you haven’t worked anything out by then.

 

I've got a bed rack for ya

 

Nice. I could come meet you and drop it off sometime before the 19th if you're willing to do this!

 

Yeah that’s fine. I pass by that intersection twice a day. Live at Kipling and Coal Mine

 

Sent message to you both.

 

I have a few things for sale.

Yakima roof rack with fairing. Had it on my 07', should fit 05-15, im not sure about 1st or 2nd gens. $200
ARB premium recovery kit. I only used the tree saver a few times, still in great shape. I haven't used anything else in the kit. $300
Two cv axles from a 2nd gen. Not sure about mileage, but they would make great spares incase you break one. $75

Located in Broomfield, CO

 

@07amocat OEM CVs?

 

@binge_stinker I think so, but I'm not 100% sure

 

@Sub-Zero

 

https://denver.craigslist.org/cto/d/littleton-1978-fj-40-landcruiser/7014437015.html

 

DeWalt flex volt cordless angle grinder. $75 OBO

Bought used not realizing that it would not work with standard DeWalt 20V batteries



Traxxas Revo 2.5(?) nitro rc truck

Badass truck, haven't run it in about 2 years because I spend my time on my Tacoma instead Has Traxxas long travel kit, I have original manuals and a nice charger for batteries, fuel bottles etc. Some new parts like a gear and differential locker

$175 OBO

Need new batteries and probably fuel lines.