Show off your Cooper ST Maxx

I’ve got spc adjustable uca’s. I’ve got my lower control arm caster adjustment maxed out pushing the wheel as far forward as possible and dialed in the rest from the top uca adjuster. Using just a level, some fishing line, a jack stand and hours of minute adjustments I’ve got it driving pretty good.

I had to trim the fender a tad front and rear. Tested flex using a jack and just barely touches the cab mount at full flex at about 3/4 turn. Not enough to worry about at this point. I’ll have to see what quick flex hits to the front suspension do as far as rubbing. But so far no cmc and no rub after my trimming.

 

Did some wheeling over the holidays, a decent amount being in snow, and the tires did great. I'm still super happy with the purchase and have about 10k miles on them now.

 

Truck looks sweet! Seems as the pull to the right issue is pretty widespread.. I work at a shop so I'm not too worried about the wheels getting scratched..

Seems the "pull to the right" issue is pretty consistent.. Thanks for the pics and info

 

315s, had 285s for a few years which were awesome

 

New shoes

 

havn't chalk tested yet but curious what others psi are on 285/75/16's. i'm currently at about 31~32 on all 4 once warmed up, 29~30 cold. seem to handle fine so far.

 

Just installed yesterday. 265/65r17 Cooper ST Maxx. Enjoying them so far!

 

Had these put in today and already had a ride through the quarry. 265/75-16 E’s. They replaced the same size BFG K02 E Codes.

I noted the Coopers ride much softer at the same 38 PSI. The BFG’s were bouncy conspired to the Coopers that are much smoother over rough surfaces. But the BFGs had much better steering feel. The coopers feel disconnected and vague but at low speeds the coopers turn with a lot less effort. It feels like I got a new steering rack. Very interesting difference, curious how it will play over the next 1000 mines.

 

Chalk tested 285/75/16 on my 2019 DCSB SR5 4x4. Front 29psi rear 25psi. seems kinda low. this was cold so they'll heat up to about 32/28. Gonna run em like this for a bit and see how they do.

 

this was my zone when i ran the Maxx tires (2 sets), not too low, but you can go a bit higher if you prefer it without any issues. I'm on AT3LTs now and the pressures are about the same. they use the same tire carcass spec.

 

right on! Good to know. Man. How’d u like the Maxx?

 

I'm running down my AT3s in a hurry hoping to get a new set of Maxx's to replace them. they are great in E range.

 

Third set of Max’s (different trucks) still love them!

 

Hi, anybody else here running them in stock 3rd Gen size like "rtheisens" a few Posts above does (265/65/17) and willing to share some pics? Want to upgrade my Hilux with tougher tires this spring, still not decided between the ST Maxx and BFG KO2's. Want to stay stock size cause going up any bigger is a hassle here in Germany. Also, price for the BFG's is about 40,- Euros more per tire here, and according to all I read online people who had both tires give their vote to the Maxx mostly... seemingly it's the better tire for less money?
Cheers, Stefan

 

looking nice! do yours pull slightly to the right? if not do you have alignment speccs you can share?

 

No pull. My alignment sheet is about 600 miles away. I can snatch a photo when I get home on Thursday.

 

right on man. Thank you. Safe travels.

 

Anyone running these with scs f5 0 offset?255/85/16 st Maxx is really appealing just don’t want to mess with my cab mount

 

I ran them on F5s with the 0 offset on 16s and never had to do a CMC, I did have to heatgun the mud flaps a tiny bit though to eliminate all rubbing

 

Nice. Have you switched to a different setup since then? Suspension stock? Any pictures of the combo.