What Have You Done To Your 3rd Gen Today?

RivetNutBob · Feb 23, 2020

TroyFJ said: ↑

Here's what I did: (It all started when I drove about 30 miles in a light snow storm, and I was deeply disappointed by my truck's performance. Clearly, I needed new tires. But, I didn't want the same size tires... so)

I added a 2" lift, installed it myself. It took my friend 4 hours to do a very similar lift on his truck, it took me ALL weekend. So, that's not bad... I got Goodyear Duratracs, 265/75R16. I added 1.25" wheel spacers, as I didn't want to spend the money on new rims right now. I would have like to have gone with 285's, but they required wider rims. I actually still like the stock rims, even though I see them everywhere. I'll buy new rims and go to 285's when these tire wear out.

This was stock:

And after lift and tires:

I added a 3TPAM, I love it. Although, I was disappointed that it doesn't really have a way of routing wires into the dash. My whole point was I wanted everything to look very clean, with no wires running everywhere. So, I drilled a hole in the wiring cover, and then I drilled a hole in the top of the bezel on the driver's side. This actually worked out well.

I got a Yaesu FT-8900R, though I don't yet have my license. Still studying. I got a Nextbase 522GW dash cam with a rear facing cam. I mounted it where I did because in Nevada, technically you're not supposed to put anything in the windshield except for the bottom right 6" X 6" square area. I made brackets for the Ham Radio and the dash cam from misc. hardware and painted them flat black. The dash cam vibrates a little, but I can live with that. I got an Auxiliary Fuse Block Bracket from Overland Equipped. I was actually very disappointed, immediately after install, my power brakes went out. Turns out the top edge of the bracket cut through a brake wire housing and blew the jcase fuse.

So, I cut the bracket, it fits much better now.

I got a Blue Sea 5032 12 circuit split buss fuse block, as I wanted to have some accessories always powered, like a usb charger, and some accessories to turn on and off with the ignition, or accessory. I got a 100 amp circuit breaker, and a 75 amp relay. To switch the relay, Caribe Makaira (a well known user on Tacoma World) spend the better part of a Saturday walking me through how to wire to the underside of my fuse block. This was probably the toughest part of all of this for me. The relay box is tricky to get out. Once I did, I tried to pull the green wire out (The one just to the left of the big yellow one) so I could re-crimp the two wires together, I suspect it is not a slip on connection, it wouldn't come out. So, I just wedged a male connecter in and wired it all back up. It's working great.

That big bundle of wires on the right is for when my Southern Style Slimline bumper with a 20" LED Light Bar gets here. I ordered it 12 weeks ago (this Tuesday) from Vivid Racing. They said to allow 10-12 weeks for fabrication. There's also a wire for rear lights if I ever order the

$646 Body Armor TC-2963 Body Armor 2016-2022 Compatible With Toyota Tacoma Pro Series Rear Bumper Black TC-2963

Body Armor TC-2963 PRO Series rear bumper I want, with the 2" Square Flush Mount CREE LED Lights.

I also got some switches for the lights, and I like the idea of having a voltmeter.

Anyway, that is about it. Just waiting on my bumper (I did buy a WARN 8000LB winch, a synthetic winch cable and a WARN aluminum hawse fairlead. I'm thinking about an Ultra Hook from Factor 55).

I like my Tacoma even better now that I've put some work into it!
Click to expand...

Holy Moley, you been busy! Lookin' good Bud!!

RivetNutBob · Feb 23, 2020

gurneyeagle said: ↑

My first car was a '70 Plum Crazy Dodge Super Bee, 383 with a four speed. It had "only" 60K miles.
Lasted all of 3 weeks before the engine blew!

My dad bailed me out by buying me a Honda Civic that I drove for two years. When the '79 gas crisis hit six months later, I wasn't as disappointed.
Click to expand...

A Super Bee? Bet you wish you still had it!

GamerAngler · Feb 23, 2020

Got windows tinted. Geoshield Pronano Ceramic. 20% on fronts, 35% on rears. From inside it looks like an EXACT match. From the outside, if looking carefully, it looks like the fronts are just sliiightly lighter than the backs, which was the goal.

I've also removed the air dam on the front (not pictured).

Up next, Amber LED fog light bulb replacement, and maybe some interior footwell LED's if I can manage to figure out how to wire it up the way I want.

RivetNutBob · Feb 23, 2020

JuanVenado said: ↑

Just so y'all know I get this "modding" bug honest. This is my Mom's HL. She's 68 years old, and she did most of this on her own, lol

Click to expand...

Good for Mom! God Bless her!!

RivetNutBob · Feb 23, 2020

Round the world said: ↑

Can’t believe that Toyota would have radio nearly flat knobs adjacent to the touch screen. Does @Tacowiede have a website?
Click to expand...

I don't recall, just send him a PM and ask. I'm sure he'll respond one way or another.

RivetNutBob · Feb 23, 2020

Marek71 said: ↑

Wow I remember drive-ins hadn't thought about them for ages.
Click to expand...

Back in the day Friday night was cruise night. Everyone would go to Abdows Big Boy and show off their rides. I'd usually order up a Brawny Lad, some fries and a Coke, Car hops were the bomb, sure miss those days. Saturdays were usually spent with my significant other, now the Mrs. A six pack, french fries and one of those horrible drive-in pizzas. Life was good! I feel sorry for a lot of the younger crowd that never got to experience those times, they're all but gone now.
Good times and a lot of good clean fun!

Brownie_Man · Feb 23, 2020

oostroma said: ↑

So what are the consequences of having your pistol stolen from your vehicle?
Click to expand...

For many, a holster in the truck like you saw, is used only while driving. If one wears their sidearm on their hip, it can get uncomfortable while driving. Especially, if one conceal carries their pistol IWB.

Round the world · Feb 23, 2020

TRD4X4TOY said: ↑

I bought this very useful obd2 scanner. Can read many different parameters. The 0 to 60 was a fun test ( 2 people in the truck and loaded with about an extra 150 to 200 pounds). You can also do 60 to 0 stop test etc. I needed this for one of my other vehicles and then I tested it on the Tacoma. It also has data logging which is a plus.
Click to expand...

Nice! What model is your OBD II?

Round the world · Feb 23, 2020

TK11 said: ↑

Thought I was making a witty reply that maybe his neighborhood was a bit too dangerous, but I see there's a different interpretation. I wasn't anticipating being stereotyped, but these forums can be entertaining. Oh well. By the way, I may live in CA but I am not against gun ownership or freedom. Rock on, fellas!
Now back to our regularly scheduled programming...
Click to expand...

Nah you’re good

RivetNutBob · Feb 23, 2020

56 degrees tomorrow. Thinking I might even do a mod or two. Maybe the behind the cab accessory rail and a second one secured lower with some rivet nuts so I can securely Mount my recovery treads and maybe my 4 lb. extinguisher if there is enough room.

bcgill · Feb 23, 2020

Busy weekend working on the Taco. Installed a Meso custom lower switch panel and puddle light switch.

Also installed a third bed rail and some mounts I fabricated for the quick fists in the bed.

Nomad26 · Feb 23, 2020

Round the world said: ↑

Can’t believe that Toyota would have radio nearly flat knobs adjacent to the touch screen. Does @Tacowiede have a website?
Click to expand...

www.tacomods.com

Tacman19 · Feb 23, 2020

Finished the stock grill copycat raptor lookalike lights..

pochoboy · Feb 23, 2020

we got and done our 1st mod for our pet Tacoma, Opti-Coat Pro.

RivetNutBob · Feb 23, 2020

pochoboy said: ↑

we got and done our 1st mod for our pet Tacoma, Opti-Coat Pro.
Click to expand...

Welcome to TW M8!

CementTacoPA · Feb 23, 2020

Easthill Bob said: ↑

Back in the day Friday night was cruise night. Everyone would go to Abdows Big Boy and show off their rides. I'd usually order up a Brawny Lad, some fries and a Coke, Car hops were the bomb, sure miss those days. Saturdays were usually spent with my significant other, now the Mrs. A six pack, french fries and one of those horrible drive-in pizzas. Life was good! I feel sorry for a lot of the younger crowd that never got to experience those times, they're all but gone now.
Good times and a lot of good clean fun!
Click to expand...

I’ve got a drive in movie theater about an hour from me. My wife and I went maybe 3 times last summer now that I’ve got the truck. A few old couch cushions, my old college comforter, and a portable speaker and we had a blast!

RallySOP · Feb 23, 2020

Easthill Bob said: ↑

I had a '65 Chey Super Sport with a 283 and a jetted Rochester Quadrojet. When you hit passing gear that thing would snap your head back. For a 283 that thing got out of its own way.
Memories.
Cruising, Drive-Ins, Car Hops, those were the days!
Click to expand...

Wow! I can’t remember how many times I rebuilt my quadrajunk before I saved up for a holley. Memories!

TheTaco510 · Feb 23, 2020

2018 Tacoma TRD Sport

Added a soft bed tonneau cover

Changed headlight and fog lights to LEDs

Changed interior lights to LEDs

Added side steps

Sound system: 2 10” JL W1v2-4 subs in an enclosed box, JL XD1000/5v2 amp, JL C2 tweeters, 6x9s, and 6 1/2s, AudioControl Epicenter, JL LoC-22 all on the stock stereo

TRD Pro grill

RivetNutBob · Feb 23, 2020

RallySOP said: ↑

Wow! I can’t remember how many times I rebuilt my quadrajunk before I saved up for a holley. Memories!
Click to expand...

Once jetted right they weren't too bad.
I couldn't afford a Holly back then but yeah that would have been the way to go. My Dad knew how to squeeze the most out of a motor without spending a lot of cash so for me that Quadrajet worked just fine. That thing ran like a top thanks to him.

RivetNutBob · Feb 23, 2020

TheTaco510 said: ↑

2018 Tacoma TRD Sport

Added a soft bed tonneau cover

Changed headlight and fog lights to LEDs

Changed interior lights to LEDs

Added side steps

Sound system: 2 10” JL W1v2-4 subs in an enclosed box, JL XD1000/5v2 amp, JL C2 tweeters, 6x9s, and 6 1/2s, AudioControl Epicenter, JL LoC-22 all on the stock stereo

TRD Pro grill

Click to expand...

Welcome to TW Bud!

Log in or Sign up

Welcome to Tacoma World!

What Have You Done To Your 3rd Gen Today?

#148561
RivetNutBob Right Ain't Wrong and Left Ain't Right.

#148562
RivetNutBob Right Ain't Wrong and Left Ain't Right.

#148563
GamerAngler Well-Known Member

#148564
RivetNutBob Right Ain't Wrong and Left Ain't Right.

#148565
RivetNutBob Right Ain't Wrong and Left Ain't Right.

#148566
RivetNutBob Right Ain't Wrong and Left Ain't Right.

#148567
Brownie_Man Well-Known Member

#148568
Round the world Well-Known Member

#148569
Round the world Well-Known Member

#148570
RivetNutBob Right Ain't Wrong and Left Ain't Right.

#148571
bcgill Well-Known Member

#148572
Nomad26 Well-Known Member

#148573
Tacman19 Well-Known Member

#148574
pochoboy Well-Known Member

#148575
RivetNutBob Right Ain't Wrong and Left Ain't Right.

#148576
CementTacoPA Well-Known Member

#148577
RallySOP Well-Known Member

#148578
TheTaco510 Member

#148579
RivetNutBob Right Ain't Wrong and Left Ain't Right.

#148580
RivetNutBob Right Ain't Wrong and Left Ain't Right.

Products Discussed in

Log in or Sign up

Useful Searches

Welcome to Tacoma World!

What Have You Done To Your 3rd Gen Today?

#148561 RivetNutBob Right Ain't Wrong and Left Ain't Right.

#148562 RivetNutBob Right Ain't Wrong and Left Ain't Right.

#148563 GamerAngler Well-Known Member

#148564 RivetNutBob Right Ain't Wrong and Left Ain't Right.

#148565 RivetNutBob Right Ain't Wrong and Left Ain't Right.

#148566 RivetNutBob Right Ain't Wrong and Left Ain't Right.

#148567 Brownie_Man Well-Known Member

#148568 Round the world Well-Known Member

#148569 Round the world Well-Known Member

#148570 RivetNutBob Right Ain't Wrong and Left Ain't Right.

#148571 bcgill Well-Known Member

#148572 Nomad26 Well-Known Member

#148573 Tacman19 Well-Known Member

#148574 pochoboy Well-Known Member

#148575 RivetNutBob Right Ain't Wrong and Left Ain't Right.

#148576 CementTacoPA Well-Known Member

#148577 RallySOP Well-Known Member

#148578 TheTaco510 Member

#148579 RivetNutBob Right Ain't Wrong and Left Ain't Right.

#148580 RivetNutBob Right Ain't Wrong and Left Ain't Right.

Products Discussed in Entire Site Forum: 3rd Gen. Tacomas (2016-2023) Thread: What Have You Done To Your 3rd Gen Today?

#148561
RivetNutBob Right Ain't Wrong and Left Ain't Right.

#148562
RivetNutBob Right Ain't Wrong and Left Ain't Right.

#148563
GamerAngler Well-Known Member

#148564
RivetNutBob Right Ain't Wrong and Left Ain't Right.

#148565
RivetNutBob Right Ain't Wrong and Left Ain't Right.

#148566
RivetNutBob Right Ain't Wrong and Left Ain't Right.

#148567
Brownie_Man Well-Known Member

#148568
Round the world Well-Known Member

#148569
Round the world Well-Known Member

#148570
RivetNutBob Right Ain't Wrong and Left Ain't Right.

#148571
bcgill Well-Known Member

#148572
Nomad26 Well-Known Member

#148573
Tacman19 Well-Known Member

#148574
pochoboy Well-Known Member

#148575
RivetNutBob Right Ain't Wrong and Left Ain't Right.

#148576
CementTacoPA Well-Known Member

#148577
RallySOP Well-Known Member

#148578
TheTaco510 Member

#148579
RivetNutBob Right Ain't Wrong and Left Ain't Right.

#148580
RivetNutBob Right Ain't Wrong and Left Ain't Right.

Products Discussed in