**ALL SOLD** Mobtown, SwitchPros, Fox, Hondo Un-Holey (N. Virginia)

Traded in the 3rd gen... hopefully the 4th has a better payload and an AT that I can live with so my wife will enjoy wheeling but in the mean time I've turned to the dark side to check all the boxes. On that new truck high in a good mood so this is priced to sell because I seriously owe my wife something nice now.

Located west outside the DC beltway and I'm willing to drive a few hours for the pricier parts or anywhere along 81/40 between DC and Knoxville TN. Will ship where noted at your expense.

NOTE: I'm keeping order of inquiries on the small stuff and will offer it up in order but on the large stuff, it's first come, first served. Shipping will be a bitch on the suspension and bumper so I'll sell to the first person to show me the money or at the least, a deposit via paypal.



Fox 2.5 Rear Shocks - Smoothie w/ Reservoir (FOX-883-24-007) - $700

Same deal, brand new, in the storage unit, will get pics and update. Good for a 1.5" lift but would just cost you a little down travel if you went higher.

Fox 2.5 Front Shocks - Emulsion Coilover (FOX-883-02-025) $1,000

Same deal, brand new, in the storage unit, will get pics and update. Will need UCAs for these or they are likely to contact the arm on full droop. Good for up to a 3" lift.

Will do the full Fox set for $1,500 if you want both.


TRD Off-Road Wheel and Tire - $100

Need to get a stem installed and seat the bead but the tire is barely worn. Picked this up so I'd have a matching wheel for the bumper tire carrier and never installed either of them.



[SOLD] Mobtown Standard Plate Rear Bumper w/ Dual Swing-Out - $1500

Sold for $1400 picked up locally

Picked this up last month, never installed. Includes all hardware and no wait. List is like $2300 with powder.





[SOLD] SwitchPros

$659 SP9100 Switch Pros SP-9100 8-Switch Panel Power System With Concealed Mounting Hardware

SP9100 w/ SDHQ Tacoma bracket USED - $350 (will ship)

Nice under-hood install bracket that goes under your clutch reservoir or uses those holes on your driver inner fender if you bought an inferior truck.

The kicker: (1) You will need new labels ($14 via SP) for the panel as I lost them. (2) You will need to splice the 4-pin communications cable or get a new one (Confirmed $39 directly from SP and you have to call) because I cut it when I couldn't find my pin tool as the connector doesn't fit through any standard firewall hole. It's fine wiring so splicing might be a bitch on this one. There's about 5' of cable on the main unit side so you could probably just redo the molex on the head unit side if you have the tools.

4AWG main power with a Blue Sea MBRF fuse at the terminal that you can connect under the batt(+) nut. I upgraded the wiring to 12awg (actual molex pins using the actual expensive AF molex crimper) and the leads are generally long enough to just use straight out of the unit instead of the 2' leads that you normally get on the thing.

This does not require additional fuses as it's solid-state so no external fuses or relays required.




[SOLD] Hondo Un-Holey v2 w/ RAM Ball Mount - $25 EA or $40 for both (will ship)
Good condition and surprisingly stable. Ran these with a 6th gen iPad (on a very short arm) and they did just fine.




[SOLD] Mobtown Weld-On Rock Sliders - short wheelbase - $200

Hope this can slide without pics as it's in my storage unit but they're unfinished and there are a few parts to be welded on aside from just slapping it onto the frame. I'm planning on heading out that way this week sometime and will update with pics before sale.

 

@hoarder23

 

@velogeek I'll take the SwitchPro. PM incoming

 

Does this version of the Hondo garage allow for the vents to be opened or closed?

 

PM’d for Hondo Un-Holey v2, I’ll take both.

 

Not really. You get about half the normal movement but they don't fully open or come anywhere near closing.

 

You are #2... someone beat you via PM by like 5 mins.

 

Second in line for the switch pro.

PM inbound.

 

Thanks

 

@AR15xAR10 sliders

 

PM sent

 

What cab/bed are the sliders for?
Thanks
Shubey

 

Probably should have said that but short wheelbase.

 

How has noone scooped that rear bumper yet?!

 

Probably because it's 190 lbs according to Mobtown and it's probably gotta be local haha.

 

Interested in shocks and sliders, located in central VA

 

Sliders someone has a deposit down and I'm meeting them this weekend or next. Shocks have inquiries but nobody has committed.

Making a note in the post about first come first served on the big ticket stuff so if you're interested, I can meet up this weekend for the suspension.

 

A few updates to the original post for those tracking, Switch-Pro and Un-Holey mounts sold; sliders have a deposit and a pending sale in person in the next week or two.

 

Really tempted by the rear bumper and I'm close enough to make Knoxville a thing........

 

Negatory on the weld ons. You know this doggy.